Chitosan is a biopolymer widely used for biomedical applications such as drug delivery systems, wound healing, and tissue engineering. Chitosan can be used as coating for other types of materials such as iron oxide nanoparticles, improving its biocompatibility while extending its range of applications.

In this work iron oxide nanoparticles (Fe3O4 NPs) produced by chemical precipitation and thermal decomposition and coated with chitosan with different molecular weights were studied. Basic characterization on bare and chitosan-Fe3O4 NPs was performed demonstrating that chitosan does not affect the crystallinity, chemical composition, and superparamagnetic properties of the Fe3O4 NPs, and also the incorporation of Fe3O4 NPs into chitosan nanoparticles increases the later hydrodynamic diameter without compromising its physical and chemical properties. The nano-composite was tested for magnetic hyperthermia by applying an alternating current magnetic field to the samples demonstrating that the heating ability of the Fe3O4 NPs was not significantly affected by chitosan.

This work reports the optimization of V2O5 Seebeck coefficient to obtain high sensitivity and transparent temperature sensors. It is observed that the film thickness plays a major role on the thermoelectric properties, together with the annealing step, obtaining a Seebeck coefficient of −690 μV K−1, for 75 nm thick V2O5 films deposited on glass, after an annealing step of 1 h at 773 K, in air. The V2O5 films are also deposited and optimized on polyimide substrates, but lower annealing temperature is required, 573 K for 3 h, to maintain the flexibility of the substrate and simultaneously high Seebeck coefficient, −591 μV K−1. These films are used in a simple design sensor and tested on the surface of a microfluidic channel (500 μm) made of polydimethylsiloxane, while having hot water flowing through it. The response time is below 1 s and the recovery time around 5 s.

The intense light scattered from metal nanoparticles sustaining surface plasmons makes them attractive for light trapping in photovoltaic applications. However, a strong resonant response from nanoparticle ensembles can only be obtained if the particles have monodisperse physical properties. Presently, the chemical synthesis of colloidal nanoparticles is the method that produces the highest monodispersion in geometry and material quality, with the added benefits of being low-temperature, low-cost, easily scalable and of allowing control of the surface coverage of the deposited particles. In this paper, novel plasmonic back-reflector structures were developed using spherical gold colloids with appropriate dimensions for pronounced far-field scattering. The plasmonic back reflectors are incorporated in the rear contact of thin film n-i-p nanocrystalline silicon solar cells to boost their photocurrent generation via optical path length enhancement inside the silicon layer. The quantum efficiency spectra of the devices revealed a remarkable broadband enhancement, resulting from both light scattering from the metal nanoparticles and improved light incoupling caused by the hemispherical corrugations at the cells' front surface formed from the deposition of material over the spherically shaped colloids.

The influence of Ag nanoparticles (Ag NPs) on the luminescence of electrospun nonwoven mats made of polyvinylpyrrolidone (PVP) has been studied in this work. The PVP fibers incorporating 2.1–4.3 nm size Ag NPs show a significant photoluminescence (PL) band between 580 and 640 nm under 325 nm laser excitation. The down conversion luminescence emission is present even after several hours of laser excitation, which denotes the durability and stability of fibers to consecutive excitations. As so these one-dimensional photonic fibers made using cheap methods is of great importance for organic optoelectronic applications, fluorescent clothing or counterfeiting labels.

The eutrophication of surface waters caused by cyanobacteria is a worldwide problem, leading to expensive
water treatment costs [1]. In addition, the production of microcystins by these microalgae may cause many
health problems to humans and animals (e.g. liver cancer) and even death [2]. Therefore, a variety of
methods have been developed to control cyanobacteria blooms, including physical and chemical treatments.
However, they have negative impacts on other species of (micro) algae and on other aquatic biota. As a
consequence, ultrasonic algae treatment has been proposed as a clean approach to controlling the blooms of
some algae species and microcystins degradation [3]. Still, the specific effects of ultra-sonication on
cyanobacteria are not well known. The present work aimed to study the effects of ultra-sonication on the
cyanobacteria structure under different ultrasound conditions (changing frequency and power) by using
conventional histology and electron microscopy methods.
Microcystis spp. were harvested in a lake from Azores (Portugal) and stored in the cool and dark until
transported to the laboratory. Cyanobacteria were cultured in liquid BG-11 axenic medium at 22ºC in an
incubator chamber, under continuous illumination (fluorescent cold white light).
Samples were collected and suspensions of cells (1ml each) were subjected to ultrasonic irradiation using
diverse ultrasonic equipment (UP100H; UP200S, sonoreactor UTR 200 and ultrasonic bath) and testing
different exposure times. All the experimental algal suspensions were exposed for 5 min to ultrasonication
(on ice for periods of 10s to avoid heating). After ultrasonication cyanobacteria growth was assessed for a
period of 14 days and structural changes in cells were evaluated by light (LM) and scanning electron
microscopy (SEM) examination. The results show growth inhibition of the cyanobacteria according to
intensity and power used in each ultrasonic device. The use of the most powerful devices (sonoreactor and
UP200S) resulted in a massive disrupting of cell walls with consequent cell death (Fig. 1e,f). Similar results
were obtained by Ahan et al. [1] and Nakano et al. [4] and showing cell wall disruption. However, even
after exposure to the most powerful instrumentation it was possible to detect some viable cells and after 14
days colonies were already visible. The results from light and electron microscopy showed noticeable
changes at the structural level such as disruption of cell gas vacuoles (arrowhead), colony disaggregation and
damage of cell walls of cells (Fig. 1c-f).
As a consequence, the use of ultrasounds to improve water quality from eutrophic waters must be considered
with careful in terms of efficiency and other complementary methods should be considered to assure good
water quality criteria. In addition, the effects of ultrasonication in other aquatic organisms require further
studies before using this technology to control algae blooms.

The search for materials with suitable thermoelectric properties that are environmentally friendly and abundant led us to investigate p- and n-type hydrogenated nanocrystalline silicon (nc-Si:H) thin films, produced by plasma-enhanced chemical vapor deposition. The Seebeck coefficient and power factor were measured at room temperature showing optimized values of 512 µV K−1 and 3.6 × 10−5 W m−1 K−2, for p-type, and −188 µV K−1 and 2.2 × 10−4 W m−1 K−2, for n-type thin films. The thermoelectric output power of one nc-Si:H pair of both n- and p-type materials is ~91 µW per material cm3, for a thermal gradient of 8 K. The output voltage and current values show a linear dependence with the number of pairs interconnected in series and/or parallel and show good integration performance.

The new properties of engineered nanoparticles drive the need for new knowledge on the safety, fate, behavior and biologic effects of these particles on organisms and ecosystems. Titanium dioxide nanoparticles have been used extensively for a wide range of applications, e.g, self-cleaning surface coatings, solar cells, water treatment agents, topical sunscreens. Within this scenario increased environmental exposure can be expected but data on the ecotoxicological evaluation of nanoparticles are still scarce. The main purpose of this work was the evaluation of effects of TiO2 nanoparticles in several organisms, covering different trophic levels, using a battery of aquatic assays. Using fish as a vertebrate model organism tissue histological and ultrastructural observations and the stress enzyme activity were also studied. TiO2 nanoparticles (Aeroxide® P25), two phase composition of anatase (65%) and rutile (35%) with an average particle size value of 27.6±11 nm were used. Results on the EC50 for the tested aquatic organisms showed toxicity for the bacteria, the algae and the crustacean, being the algae the most sensitive tested organism. The aquatic plant Lemna minor showed no effect on growth. The fish Carassius auratus showed no effect on a 21 day survival test, though at a biochemical level the cytosolic Glutathione-S-Transferase total activity, in intestines, showed a general significant decrease (p<0.05) after 14 days of exposure for all tested concentrations. The presence of TiO2 nanoparticles aggregates were observed in the intestine lumen but their internalization by intestine cells could not be confirmed.

A MATLAB/SIMULINK software simulation model (structure and component blocks) has been constructed in order to view and analyze the potential of the PSD (Position Sensitive Detector) array concept technology before it is further expanded or developed. This simulation allows changing most of its parameters, such as the number of elements in the PSD array, the direction of vision, the viewing/scanning angle, the object rotation, translation, sample/scan/simulation time, etc. In addition, results show for the first time the possibility of scanning an object in 3D when using an a-Si:H thin film 128 PSD array sensor and hardware/software system. Moreover, this sensor technology is able to perform these scans and render 3D objects at high speeds and high resolutions when using a sheet-of-light laser within a triangulation platform. As shown by the simulation, a substantial enhancement in 3D object profile image quality and realism can be achieved by increasing the number of elements of the PSD array sensor as well as by achieving an optimal position response from the sensor since clearly the definition of the 3D object profile depends on the correct and accurate position response of each detector as well as on the size of the PSD array.

The combination of high transparency and good thermoelectric properties of SnO2 can open new field of applications for the thin film thermoelectric materials. Here we report on SnO2 thin films with transmittance above 90%, resistivity bellow 10-3 Ωm and a Power Factor around 10-4 W/m.K2, for a Seebeck of -255 μV/K, at room temperature. The effect of film thickness and post-deposition annealing on the thermoelectric properties were analysed. The performances of a single layer thermoelectric device are also presented.

Photocurrent enhancement in thin a-Si:H solar cells due to the plasmonic light trapping is investigated, and correlated with the morphology and the optical properties of the self-assembled silver nanoparticles incorporated in the cells’ back reflector.