A MATLAB/SIMULINK software simulation model (structure and component blocks) has been constructed in order to view and analyze the potential of the PSD (Position Sensitive Detector) array concept technology before it is further expanded or developed. This simulation allows changing most of its parameters, such as the number of elements in the PSD array, the direction of vision, the viewing/scanning angle, the object rotation, translation, sample/scan/simulation time, etc. In addition, results show for the first time the possibility of scanning an object in 3D when using an a-Si:H thin film 128 PSD array sensor and hardware/software system. Moreover, this sensor technology is able to perform these scans and render 3D objects at high speeds and high resolutions when using a sheet-of-light laser within a triangulation platform. As shown by the simulation, a substantial enhancement in 3D object profile image quality and realism can be achieved by increasing the number of elements of the PSD array sensor as well as by achieving an optimal position response from the sensor since clearly the definition of the 3D object profile depends on the correct and accurate position response of each detector as well as on the size of the PSD array.

The unique properties of electrospun nanofibers combined with functional compounds allow the preparation of novelty materials that can be employed in a wide range of applications. Among a vast number of polymers, Cellulose Acetate (CA) it is considered easy to electrospun and it was employed as the polymeric matrix, where free and iridium-porphyrins were incorporated. Two different solvent systems were employed according to the porphyrin used, and the best dispersion level on both the electrospun solution and the membranes, was achieved with the iridium porphyrin. The nanofibers with this porphyrin also exhibited electrical properties, while the fluorescence was quenched by the presence of specific axial ligands.

The incorporation of magnetic nanoparticles into poly(N-isopropylacrylamide) (PNIPAAm) and chitosan microgels gives rise to hybrid systems that combine the microgels swelling capacity with the interesting features presented in magnetic nanoparticles. The presence of chitosan that act as surfactant for magnetic nanoparticles provides a simplistic approach which allows the encapsulation of magnetic nanoparticles without any previous surface modification. Spherical and highly monodisperse microgels with diameters in the range of 200 to 500 nm were obtained. The encapsulation of magnetic nanoparticles in the polymer matrix was confirmed by high resolution Scanning Electron Microscopy in transmission mode. Volume phase transition of the microgels was accessed by Dynamic Light Scattering measurements. It was observed that the thermosensitivity of the PNIPAM microgels still persists in the hybrid microgels; however, the swelling ability is compromised in the microgels with highest chitosan content. The heating performance of the hybrid magnetic microgels, when submitted to an alternating magnetic field, was also evaluated demonstrating the potential of these systems for hyperthermia treatments.

Recent studies show the incorporation of graphene oxide (GO) in cement composites. But these composites are frequently incompatible with original materials for building rehabilitation. To overcome this limitation, natural hydraulic lime mortars were used as matrix, and the influence of GO percentage and type of mixing was investigated. The influence on the microstructure, mechanical and physical properties was assessed. The best results were obtained with dispersed GO at concentrations of 0.05% and 0.1%. A slight improvement of mechanical and physical characteristics was achieved. This could lead to new mortars with improved properties that can be used for building rehabilitation.

Developments in thermoelectric (TE) transparent p-type materials are scarce and do not follow the trend of the corresponding n-type materials – a limitation of the current transparent thermoelectric devices. P-type thermoelectric thin films of CuI have been developed by three different methods in order to maximise optical transparency (>70% in the visible range), electrical (σ = 1.1 × 104 Sm−1) and thermoelectric properties (ZT = 0.22 at 300 K). These have been applied in the first planar fully transparent p-n type TE modules where gallium-doped zinc oxide (GZO) thin films were used as the n-type element and indium thin oxide (ITO) thin films as electrodes. A thorough study of power output in single elements and p-n modules electrically connected in series and thermally connected in parallel is inclosed. This configuration allows for a whole range of highly transparent thermoelectric applications.