Extracts from plants have considerable significance as bioactive compounds with several pharmacological applications. Polyphenols have attracted the attention as anti-inflammatory and anti-oxidative materials. Nonetheless, the amount of these compounds in the extracts is typically very low. Consequently, green extraction techniques with higher efficiency for phenolic compounds are of paramount importance. Ionic liquids (ILs), which are also known as designer solvents can be used to extract polyphenols, however the search for ideal solvents is mostly done by trial and error. In this work, nuclear magnetic resonance (NMR) is used to study the profile of ILs molecular interactions with model compounds that mimic polyphenols. The ILs that exhibit the strongest molecular interactions were proven to have the highest efficiency when extracting polyphenols from matcha Japanese green tea, known to be extremely rich in these compounds. Both the IL cation and anion have an influence on the solvent behaviour. The best IL solvents for matcha polyphenols were imidazolium derivatives with shorter alkyl side chains and weakly basic anions such as tricyanomethanide, dicyanamide and triflate. Thus, the NMR approach avoids an exhaustive testing and allows the rational selection of the best ILs for the extraction.

The use of non-destructive evaluation (NDE) techniques for assessing microstructural changes in processed materials is of particular importance as it can be used to assess, qualitatively, the integrity of any material/structure. Among the several NDE techniques available, electrical conductivity measurements using eddy currents attract great attention owing to its simplicity and reliability. In this work, the electrical conductivity profiles of friction stir processed Ti6Al4V, Cu, Pb, S355 steel and gas tungsten arc welded AISI 304 stainless steel were determined through eddy currents and four-point probe. In parallel, hardness measurements were also performed. The profiles matched well with the optical macrographs of the materials: while entering in the processed region a variation in both profiles was always observed. One particular advantage of electrical conductivity profiles over hardness was evident: it provides a better resolution of the microstructural alterations in the processed materials. Moreover, when thermomechanical processing induces microstructural changes that modify the magnetic properties of a material, eddy currents testing can be used to qualitatively determine the phase fraction in a given region of the material. A qualitative relation between electrical conductivity measurements and hardness is observed.

Bacterial infections affect about 1 in 5 patients who receive a dental implant within 5 years of surgery. To avoid the implant rejection it is necessary for the development of innovative biomaterials, with addition or substitution of the ions, for implant coatings that promote a strong bond with the new host bone and antibacterial action. The objective of this work was to synthesize a bioactive glass with different silver concentrations to evaluate their antibacterial performance. The glasses were synthesized with up to 2% silver content by melt-quenching. Structural, morphological, biological, and electrical properties of all samples were studied. The biological behavior was evaluated through cytotoxicity tests and antibacterial activity. The structural analysis shows that the introduction of silver do not promote significant changes, not altering the advantageous properties of the bioglass of the bioglass. It was verified that the glasses with a silver content from 0.5% to 2%, completely prevented the growth of both Staphylococcus aureus and Escherichia coli while being nontoxic toward mammalian cells. Therefore, these bioglasses are promising materials to be used in the production of dental implants with antimicrobial activity.

The demand for better cellulose solvents has driven the search for new and improved materials to enable the processing of this polysaccharide. Ionic liquids have been debated for a long time as interesting alternatives, but the molecular details on the solubilization mechanism have been a matter of controversy. Herein, for the first time, the structure and dynamics of hydroxypropylcellulose (HPC) liquid crystal solutions were probed in the presence of imidazolium ionic liquids (ILs), conjugating rheological measurements with magnetic resonance spectroscopy. This study provides a characterization of the solutions macroscopic behaviour, where the liquid crystalline (LC) properties were maintained. Using ILs with different side chain lengths, the influence of the hydrophobic IL domain in the solvation abilities of ILs towards a cellulose derived polymer was accessed, providing experimental evidence on these interactions.

Electronic noses (E-noses), are usually composed by an array of sensors with different selectivities towards classes of VOCs (Volatile Organic Compounds). These devices have been applied to a variety of fields, including environmental protection, public safety, food and beverage industries, cosmetics, and clinical diagnostics. This work demonstrates that it is possible to classify eleven VOCs from different chemical classes using a single gas sensing biomaterial that changes its optical properties in the presence of VOCs. To accomplish this, an in-house built E-nose, tailor-made for the novel class of gas sensing biomaterials, was improved and combined with powerful machine learning techniques. The device comprises a delivery system, a detection system and a data acquisition and control system. It was designed to be stable, miniaturized and easy-to-handle. The data collected was pre-processed and features and curve fitting parameters were extracted from the original response. A recursive feature selection method was applied to select the best features, and then a Support Vector Machine classifier was implemented to distinguish the eleven distinct VOCs. The results show that the followed methodology allowed the classification of all the VOCs tested with 94.6% (± 0.9%) accuracy.

This work compares the stability and the catalytic efficiency of different ionic liquid phosphomolybdates ([BPy]3[PMo12O40] and [BMIM]3[PMo12O40]) with a cationic (propylpyridinium) functionalized mesoporous silica nanoparticle composite (PMo12O40@PPy-MSN). These were used as solid catalysts for the oxidative desulfurization of a multicomponent model diesel using hydrogen peroxide as oxidant and a polar immiscible extraction solvent. Ionic liquid ([BMIM][PF6] was successfully used as solvent to extract sulfur compounds from model diesel. The ionic liquid phosphomolybdates showed partial solubility in the ionic liquid phase, occurring some decomposition of their Keggin structure in the soluble reaction media, probably caused by their interaction with oxidant. On the other hand, the phosphomolybdate composite PMo12O40@PPy-MSN presented high structural stability and only negligible leaching occurrence after various consecutive reaction cycles. The model diesel was near complete desulfurized after 3 h and consecutive desulfurization cycles were performed without loss of activity. Therefore, the immobilization of Keggin phosphomolybdate structure [PMo12O40]3− using cationic propylpyridinium silica nanoparticle is an assertive strategy to produce stable and active heterogeneous catalysts.

Truncated sialylated O-glycans, such as cell-surface carbohydrate antigen sialyl-Tn (STn) are overexpressed by several cancer types, but not by the respective normal tissues. STn expression is associated with oncogenesis and metastatic ability of cancer cells, with reduced overall survival and lack of response to chemotherapy. Advances in nanomedicine have resulted in rapid development of biocompatible superparamagnetic iron oxide nanoparticles (SPIONs) with considerable potential in cancer treatment. Therefore, in this study SPIONs coated with oleic acid (OA) or dimercaptosuccinic acid (DMSA) were developed and characterized for internalization in two breast cancer cell lines: cell line expressing the STn antigen and the corresponding control. SPIONs with an average diameter of 8 nm showed superparamagnetic behavior and high potential to be used as magnetic hyperthermia agents. OA and DMSA coating provided high stability of SPIONs in physiological conditions while not changing their main properties. NPs internalization studies showed a higher accumulation of DMSA coated NPs in the breast cancer MDA-MB-231 WT cell line. In MDA-MB-231 cell line expressing STn both coated NPs showed a similar accumulation. Therefore, STn antigen can act as a receptor capable of detecting and covalently bind to the molecules present on NPs surface and induce their cellular uptake by endocytosis.

In this work, eco-friendly magnesium-silicide (Mg2Si) semiconducting (n-type) thermoelectric pastes for building components concerning energy-harvesting devices through 3D printing, spray and electrospinning were synthetized and tested for the first time. The Mg2Si fine powders were obtained through the combination of ball milling and thermal annealing under Ar atmosphere. While the latter process was crucial for obtaining the desired Mg2Si phase, the ball milling was indispensable for homogenizing and reducing the grain size of the powders. The synthetized Mg2Si powders exhibited a large Seebeck coefficient of ~ 487 µV/K and were blended with a polymeric solution in different mass ratios to adjust the paste viscosity to the different requirements of 3D printing, electrospinning and low-pressure spray. The materials produced in every single stage of the paste synthesis were characterized by a variety of techniques that unequivocally prove their viability for producing thermoelectric parts and components. These can certainly trigger further research and development in green thermoelectric generators (TEGs) capable of adopting any form or shape with enhanced thermoelectric properties. These green TEGs are meant to compete with common toxic materials such as Bi2Te3, PbTe and CoSb that have Seebeck coefficients in the range of ~ 290–700 μV/K, similar to that of the produced Mg2Si powders and lower than that of 3D printed bulk Mg2Si pieces, measured to be ~ 4866 μV/K. Also, their measured thermal conductivities proved to be significantly lower (~ 0.2 W/mK) than that reported for Mg2Si (≥ 4 W/mK). However, it is herein demonstrated that such thermoelectric properties are not stable over time. Pressureless sintering proved to be indispensable, but difficultly achievable by long thermal annealing (even above 32 h) in inert atmosphere at 400 °C, at least for bulk Mg2Si pieces constituted by a mean grain size of 2–3 μm. Hence, for overcoming this sintering challenge and become the silicide’s extrusion viable in the production of bulk thermoelectric parts, alternative pressureless sintering methods will have to be further explored.

An unprecedented approach towards oligosaccharides containing N-acetylglucosamine-N-acetylmuramic (NAG-NAM) units was developed. These novel bacterial cell wall surrogates were obtained from chitosan via a top down approach involving both chemical and enzymatic reactions. The chemical modification of chitosan using a molecular clamp based strategy, allowed obtaining N-acetylglucosamine-N-acetylmuramic (NAG-NAM) containing oligomers. Intercalation of NAM residues was confirmed through the analysis of oligosaccharide fragments from enzymatic digestion and it was found that this route affords NAG-NAM containing oligosaccharides in 33% yield. These oligosaccharides mimic the carbohydrate basic skeleton of most bacterial cell surfaces. The oligosaccharides prepared are biologically relevant and will serve as a platform for further molecular recognition studies with different receptors and enzymes of both bacterial cell wall and innate immune system. This strategy combining both chemical modification and enzymatic digestion provides a novel and simple route for an easy access to bacterial cell wall fragments – biologically important targets.

Control of the properties of electrospun polycaprolactone can be achieved by adjusting the acetic acid:water ratio used to dissolve and electrospin the polymer. In this work, we studied the effect of using up to 15 wt% water in the solvent mixture. Solution conductivity and viscosity and fibre morphology vary dramatically with water content and solution age. Two days after initial solution preparation, electrospinning yields regular fibres for a water content of 0 wt% and 5 wt%, irregular fibres for a 10 wt% water content and irregular and fused fibres for a 15 wt% water content. Fibres with the highest crystallinity (60%) were obtained from solutions containing 5 wt% water while the highest elastic modulus (8.6 ± 1.4 MPa) and tensile stress (4.3 ± 0.3 MPa) pertain to fibres obtained from solutions containing 10 wt% water. Enzymatic fibre degradation is faster the higher the water content in the precursor solution. Adhesion ratio of human foetal fibroblasts was highest on scaffolds obtained from precursor solutions containing 0 wt% water. Cell population increases for all scaffolds and populations quickly become equivalent, with no statistically significant differences between them. Cells exhibit a more extended morphology on the 5 wt% scaffold and a more compact morphology on the 0 wt% scaffold. In summary, a small water content in the solvent allows a significant control over fibre diameter, scaffold properties and the production of scaffolds that support cell adhesion and proliferation. This strategy can be used in soft tissue engineering to influence cell behaviour and the degradation rate of the scaffolds.