Publications

Export 23 results:
Sort by: Author Title [ Type  (Desc)] Year
Journal Article
Dias, D, Bernardo M, Lapa N, Pinto F, Matos I, Fonseca I.  2018.  Activated carbons from the Co-pyrolysis of rice wastes for Cr(III) removal. Chemical Engineering Transactions. 65:601-606.
Dias, D, Bernardo M, Matos I, Fonseca I, Pinto F, Lapa N.  2020.  Activation of co-pyrolysis chars from rice wastes to improve the removal of Cr3+ from simulated and real industrial wastewaters. Journal of Cleaner Production. 267:121993. AbstractWebsite

Chromium is one of the most important raw materials for the European Union. Adsorption has become an important process for the recovery of metals from wastewaters, which has led to a demand for low-cost and eco-friendly adsorbents. The objective of this work was to use new and renewable carbon-based adsorbents from rice wastes in the removal/recovery of Cr(III) from synthetic and real wastewaters. Rice wastes were submitted to co-pyrolysis and the resulting char was optimized through physical and/or chemical activations/treatments. A commercial activated carbon was used for comparison purposes. All adsorbents were characterized (including an ecotoxicity test for the char precursor) and submitted to Cr(III) removal assays from a synthetic solution, in which two solid/liquid ratios (S/L) were tested (5 and 10 g/L). The CO2 activated carbon at a S/L = 5 g/L was the biomass-derived adsorbent that performed better, obtaining a maximum Cr(III) uptake capacity of 9.23 mg/g comparable to the one obtained by the commercial adsorbent at the same S/L (9.80 mg/g). The good results on this biomass-derived carbon were due to the effective volatile matter removal during the activation (from 22.7 to 4.25% w/w), which increased both surface area (from <5.0 to 325 m2/g) and ash content (from 30.0 to 40.4% w/w), allowing an increase in Cr(III) removal due to ion exchange mechanism and porosity development. The best adsorbent, under optimized conditions, was also applied to a chromium rich industrial wastewater. The results obtained in this real case application demonstrated a competition effect due to the presence of other ions.

Godinho, D, Dias D, Bernardo M, Lapa N, Fonseca I, Lopes H, Pinto F.  2017.  Adding value to gasification and co-pyrolysis chars as removal agents of Cr3+. Journal of Hazardous Materials. 321:173-182. AbstractWebsite

The present work aims to assess the efficiency of chars, obtained from the gasification and co-pyrolysis of rice wastes, as adsorbents of Cr3+ from aqueous solution. GC and PC chars, produced in the gasification and co-pyrolysis, respectively, of rice husk and polyethylene were studied. Cr3+ removal assays were optimised for the initial pH value, adsorbent mass, contact time and Cr3+ initial concentration. GC showed a better performance than PC with about 100% Cr3+ removal, due to the pH increase that caused Cr precipitation. Under pH conditions in which the adsorption prevailed (pH<5.5), GC presented the highest uptake capacity (21.1mg Cr3+ g−1 char) for the following initial conditions: 50mg Cr3+ L−1; pH 5; contact time: 24h;L/S ratio: 1000mLg−1. The pseudo-second order kinetic model showed the best adjustment to GC experimental data. Both the first and second order kinetic models fitted well to PC experimental data. The ion exchange was the dominant phenomenon on the Cr3+ adsorption by GC sample. Also, this char significantly reduced the ecotoxicity of Cr3+ solutions for the bacterium Vibrio fischeri. GC char proved to be an efficient material to remove Cr3+ from aqueous solution, without the need for further activation.

Rodrigues, ARF, Maia MRG, Cabrita ARJ, Oliveira HM, Bernardo M, Lapa N, Fonseca I, Trindade H, Pereira JL, Fonseca AJM.  2020.  Assessment of potato peel and agro-forestry biochars supplementation on in vitro ruminal fermentation. PeerJ. 8:e9488. AbstractWebsite

Background The awareness of environmental and socio-economic impacts caused by greenhouse gas emissions from the livestock sector leverages the adoption of strategies to counteract it. Feed supplements can play an important role in the reduction of the main greenhouse gas produced by ruminants—methane (CH\textsubscript{4}). In this context, this study aims to assess the effect of two biochar sources and inclusion levels on rumen fermentation parameters \textit{in vitro}. Methods Two sources of biochar (agro-forestry residues, AFB, and potato peel, PPB) were added at two levels (5 and 10%, dry matter (DM) basis) to two basal substrates (haylage and corn silage) and incubated 24-h with rumen inocula to assess the effects on CH\textsubscript{4} production and main rumen fermentation parameters \textit{in vitro}. Results AFB and PPB were obtained at different carbonization conditions resulting in different apparent surface areas, ash content, pH at the point of zero charge (pHpzc), and elemental analysis. Relative to control (0% biochar), biochar supplementation kept unaffected total gas production and yield (mL and mL/g DM, \textit{p} = 0.140 and \textit{p} = 0.240, respectively) and fermentation pH (\textit{p} = 0.666), increased CH\textsubscript{4}production and yield (mL and mL/g DM, respectively, \textit{p} = 0.001) and ammonia-N (NH\textsubscript{3}-N, \textit{p} = 0.040), and decreased total volatile fatty acids (VFA) production (\textit{p} < 0.001) and H\textsubscript{2} generated and consumed (\textit{p} ≤ 0.001). Biochar sources and inclusion levels had no negative effect on most of the fermentation parameters and efficiency. Acetic:propionic acid ratio (\textit{p} = 0.048) and H\textsubscript{2} consumed (\textit{p} = 0.019) were lower with AFB inclusion when compared to PPB. Biochar inclusion at 10% reduced H\textsubscript{2} consumed (\textit{p} < 0.001) and tended to reduce total gas production (\textit{p} = 0.055). Total VFA production (\textit{p} = 0.019), acetic acid proportion (\textit{p} = 0.011) and H\textsubscript{2} generated (\textit{p} = 0.048) were the lowest with AFB supplemented at 10%, no differences being observed among the other treatments. The basal substrate affected most fermentation parameters independently of biochar source and level used. Discussion Biochar supplementation increased NH\textsubscript{3}-N content, \textit{iso}-butyric, \textit{iso}-valeric and valeric acid proportions, and decreased VFA production suggesting a reduced energy supply for microbial growth, higher proteolysis and deamination of substrate N, and a decrease of NH\textsubscript{3}-N incorporation into microbial protein. No interaction was found between substrate and biochar source or level on any of the parameters measured. Although AFB and PPB had different textural and compositional characteristics, their effects on the rumen fermentation parameters were similar, the only observed effects being due to AFB included at 10%. Biochar supplementation promoted CH\textsubscript{4} production regardless of the source and inclusion level, suggesting that there may be other effects beyond biomass and temperature of production of biochar, highlighting the need to consider other characteristics to better identify the mechanism by which biochar may influence CH\textsubscript{4} production.

Surra, E, Bernardo M, Lapa N, Esteves IAAC, Fonseca I, Mota JPB.  2019.  Biomethane production through anaerobic co-digestion with Maize Cob Waste based on a biorefinery concept: A review. Journal of Environmental Management. 249:109351. AbstractWebsite

Maize Cob Waste (MCW) is available worldwide in high amounts, as maize is the most produced cereal in the world. MCW is generally left in the crop fields, but due to its low biodegradability it has a negligible impact in soil fertility. Moreover, MCW can be used as substrate to balance the C/N ratio during the Anaerobic co-Digestion (AcoD) with other biodegradable substrates, and is an excellent precursor for the production of Activated Carbons (ACs). In this context, a biorefinery is theoretically discussed in the present review, based on the idea that MCW, after proper pre-treatment is valorised as precursor of ACs and as co-substrate in AcoD for biomethane generation. This paper provides an overview on different scientific and technological aspects that can be involved in the development of the proposed biorefinery; the major topics considered in this work are the following ones: (i) the most suitable pre-treatments of MCW prior to AcoD; (ii) AcoD process with regard to the critical parameters resulting from MCW pre-treatments; (iii) production of ACs using MCW as precursor, with the aim to use these ACs in biogas conditioning (H2S removal) and upgrading (biomethane production), and (iv) an overview on biogas upgrading technologies.

Nogueira, M, Matos I, Bernardo M, Pinto F, Lapa N, Surra E, Fonseca I.  2019.  Char from Spent Tire Rubber: A Potential Adsorbent of Remazol Yellow Dye. C—Journal of Carbon Research. 5, Number 4 AbstractWebsite

A char produced from spent tire rubber showed very promising results as an adsorbent of Remazol Yellow (RY) from aqueous solutions. Spent tire rubber was submitted to a pyrolysis process optimized for char production. The obtained char was submitted to chemical, physical, and textural characterizations and, subsequently, applied as a low-cost adsorbent for dye (RY) removal in batch adsorption assays. The obtained char was characterized by relatively high ash content (12.9% wt), high fixed-carbon content (69.7% wt), a surface area of 69 m2/g, and total pore volume of 0.14 cm3/g. Remazol Yellow kinetic assays and modelling of the experimental data using the pseudo-first and pseudo-second order kinetic models demonstrated a better adjustment to the pseudo-first order model with a calculated uptake capacity of 14.2 mg RY/g char. From the equilibrium assays, the adsorption isotherm was fitted to both Langmuir and Freundlich models; it was found a better fit for the Langmuir model to the experimental data, indicating a monolayer adsorption process with a monolayer uptake capacity of 11.9 mg RY/g char. Under the experimental conditions of the adsorption assays, the char presented positive charges at its surface, able to attract the deprotonated sulfonate groups (SO3−) of RY; therefore, electrostatic attraction was considered the most plausible mechanism for dye removal.

Dias, D, Lapa N, Bernardo M, Ribeiro W, Matos I, Fonseca I, Pinto F.  2018.  Cr(III) removal from synthetic and industrial wastewaters by using co-gasification chars of rice waste streams. Bioresource Technology. 266:139-150. AbstractWebsite

Blends of rice waste streams were submitted to co-gasification assays. The resulting chars (G1C and G2C) were characterized and used in Cr(III) removal assays from a synthetic solution. A Commercial Activated Carbon (CAC) was used for comparison purposes. The chars were non-porous materials mainly composed by ashes (68.3–92.6% w/w). The influences of adsorbent loading (solid/liquid ratio – S/L) and initial pH in Cr(III) removal were tested. G2C at a S/L of 5 mg L−1 and an initial pH of 4.50 presented an uptake capacity significantly higher than CAC (7.29 and 2.59 mg g−1, respectively). G2C was used in Cr(III) removal assays from an industrial wastewater with Cr(III) concentrations of 50, 100 and 200 mg L−1. Cr(III) removal by precipitation (uptake capacity ranging from 11.1 to 14.9 mg g−1) was more effective in G2C, while adsorption (uptake capacity of 16.1 mg g−1) was the main removal mechanism in CAC.

Rijo, B, Lemos F, Fonseca I, Vilelas A.  2020.  Development of a model for an industrial acetylene hydrogenation reactor using plant data – Part I. Chemical Engineering Journal. 379:122390. AbstractWebsite

In this work, a dynamic model of an industrial acetylene hydrogenation reactor with a front-end configuration was developed, based on plant operation data. This type of reactor operates in transient state, not only due to the natural fluctuations in operating conditions but also due to the effects caused by the deactivation of the catalyst. To develop the dynamic model of the acetylene hydrogenation reactor a thorough study of the effect of operating conditions was performed; the influence of variables such as the inlet temperature of the 1st reactor, the flowrate, carbon monoxide concentration, on the activity, selectivity and stability of the catalyst was examined by choosing adequate periods of the operation of the reactor. To understand the reaction mechanism of this system, several published kinetics were tested but only one was finally fitted to the industrial data, to interpret the operation of the acetylene hydrogenation reactor. A set of operation periods was used to develop the model which was then validated by applying the model to a different set of operation periods. As a conclusion, the dynamic model that was developed and validated, using actual plant operation data, was able to adequately describe the outlet temperatures of the three reactors in the system as well as the outlet acetylene concentration of the 3rd reactor.

Surra, E, Bernardo M, Lapa N, Esteves IAAC, Fonseca I, Mota JP.  2018.  Enhanced Biogas Production through Anaerobic co-Digestion of OFMSW with Maize Cob Waste Pre-Treated with Hydrogen Peroxide. Chemical Engineering Transactions. 65:121-126.
Fernandes, MJ, Moreira MM, Paíga P, Dias D, Bernardo M, Carvalho M, Lapa N, Fonseca I, Morais S, Figueiredo S, Delerue-Matos C.  2019.  Evaluation of the adsorption potential of biochars prepared from forest and agri-food wastes for the removal of fluoxetine. Bioresource Technology. 292:121973. AbstractWebsite

Twelve biochars from forest and agri-food wastes (pruning of Quercus ilex, Eucalyptus grandis, Pinus pinaster, Quercus suber, Malus pumila, Prunus spinosa, Cydonia oblonga, Eriobotrya japonica, Juglans regia, Actinidia deliciosa, Citrus sinensis and Vitis vinifera) were investigated as potential low-cost and renewable adsorbents for removal of a commonly used pharmaceutical, fluoxetine. Preliminary adsorption experiments allowed to select the most promising adsorbents, Quercus ilex, Cydonia oblonga, Eucalyptus, Juglans regia and Vitis vinifera pruning material. They were characterized by proximate, elemental and mineral analysis, thermogravimetric analysis, Fourier transform infrared spectroscopy, determination of specific surface area and pH at the point of zero charge. Batch and equilibrium studies were performed, and the influence of pH was evaluated. The equilibrium was reached in less than 15 min in all systems. The maximum adsorption capacity obtained was 6.41 mg/g for the Eucalyptus biochar, which also demonstrated a good behavior in continuous mode (packed column).

Bernardo, M, Rodrigues S, Lapa N, Matos I, Lemos F, Batista MKS, Carvalho AP, Fonseca I.  2016.  High efficacy on diclofenac removal by activated carbon produced from potato peel waste, Aug. International Journal of Environmental Science and Technology. 13:1989–2000., Number 8 AbstractWebsite

In the present study, a novel porous carbon obtained by K2CO3 activation of potato peel waste under optimized conditions was applied for the first time as liquid-phase adsorbent of sodium diclofenac in parallel with a commercial activated carbon. The biomass-activated carbon presented an apparent surface area of 866 m2 g−1 and well-developed microporous structure with a large amount of ultramicropores. The obtained carbon presented leaching and ecotoxicological properties compatible with its safe application to aqueous medium. Kinetic data of laboratory-made and commercial sample were best fitted by the pseudo-second-order model. The commercial carbon presented higher uptake of diclofenac, but the biomass carbon presented the higher adsorption rate which was associated with its higher hydrophilic nature which favoured external mass transfer. Both adsorbents presented adsorption isotherms that were best fitted by Langmuir model. The biomass carbon and the commercial carbon presented adsorption monolayer capacities of 69 and 146 mg g−1, and Langmuir constants of 0.38 and 1.02 L mg−1, respectively. The better performance of the commercial sample was related to its slightly higher micropore volume, but the most remarkable effect was the competition of water molecules in the biomass carbon.

Surra, E, Bernardo M, Lapa N, Esteves I, Fonseca I, Mota JP.  2018.  Maize cob waste pre-treatments to enhance biogas production through co-anaerobic digestion with OFMSW. Waste Management. 72:193-205. AbstractWebsite

In the present work, the enhancement of biogas and methane yields through anaerobic co-digestion of the pre-hydrolised Organic Fraction of Municipal Solid Wastes (hOFMSW) and Maize Cob Wastes (MCW) in a lab-scale thermophilic anaerobic reactor was tested. In order to increase its biodegradability, MCW were submitted to an initial pre-treatment screening phase as follows: (i) microwave (MW) irradiation catalysed by NaOH, (ii) MW catalysed by glycerol in water and alkaline water solutions, (iii) MW catalysed by H2O2 with pH of 9.8 and (iv) chemical pre-treatment at room temperature catalysed by H2O2 with 4 h reaction time. The pre-treatments cataysed by H2O2 were performed with 2% MCW (wMCW/v alkaline water) at ratios of 0.125, 0.25, 0.5 and 1.0 (wH2O2/wMCW). The pre-treatment that presented the most favourable balance between sugars, lignin, cellulose and hemicellulose solubilisations, as well as low production of phenolic compound and furfural (inhibitors), was the chemical pre-treatment catalysed by H2O2, at room temperature, with a ratio of 0.5 wH2O2/wMCW (Pre1). This Pre1 was then optimised testing reaction times of 1, 2 and 3 days at a different pH (11.5) and MCW percentage (10% w/v). The optimised pre-treatment that presented the best results, considering the same criteria defined above, was the one carried out during 3 days, at pH 9.8 and 10% MCW w/v (Pre2). The anaerobic reactor was initially fed with the hOFMSW obtained from the hydrolysis tank of an industrial AD plant. The hOFMSW was than co-digested with MCW submitted to the pre-treatment Pre1. In another assay, hOFMSW was co-digested with MCW submitted pre-treatment Pre 2. The co-digestion of hOFMSW + Pre1 increased the biogas yield by 38.9% and methane yield by 29.7%, when compared to the results obtained with hOFMSW alone. The co-digestion of hOFMSW + Pre2 increased biogas yield by 46.0% and CH4 yield by 36.3%. In both cases, the methane content obtained in the biogas streams was above 66% v/v. These results show that pre-treatment with H2O2, at room temperature, is a promising low cost way to valorize MCW through co-digestion with hOFMSW.

Ferreira, RC, Dias D, Fonseca I, Bernardo M, Pimenta JLCW, Lapa N, de Barros MASD.  2020.  Multi-component adsorption study by using bone char: modelling and removal mechanisms. Environmental Technology. :1-16.: Taylor & Francis AbstractWebsite
n/a
Surra, E, Nogueira MC, Bernardo M, Lapa N, Esteves I, Fonseca I.  2019.  New adsorbents from maize cob wastes and anaerobic digestate for H2S removal from biogas. Waste Management. 94:136-145. AbstractWebsite

Two activated carbons (ACs) were prepared by physical activation of Maize Cob Waste (MCW) with CO2, during 2 and 3 h (MCW(PA)2h and MCW(PA)3h, respectively). Two other ACs were prepared by chemical activation: a) MCW(LD) – MCW was impregnated with anaerobic liquid digestate (LD) and carbonized under N2 atmosphere; and b) CAR-MCW(LD) – previously carbonized MCW was impregnated with LD and carbonized under N2 atmosphere. All ACs were fully characterized for textural and chemical properties, and then used in dynamic H2S removal assays from real biogas samples. Regarding H2S removal, the ACs that were physically activated behaved much better than the impregnated ones: MCW(PA)3h and MCW(PA)2h showed H2S uptake capacities of 15.5 and 0.65 mg g−1, respectively, while MCW(LD) and CAR-MCW(LD) showed values of 0.47 and 0.25 mg g−1, respectively. This may indicate that textural properties (surface area and microporosity) are more important than mineral content in H2S removal. Effectively, both surface area and micropore volume were much higher for the samples of MCW(PA)3h (SBET = 820 m2 g−1 and Vmicro = 0.32 cm3 g−1) and MCW(PA)2h (SBET = 630 m2 g−1 and Vmicro = 0.21 cm3 g−1) than for the ACs that were chemically activated (SBET = 38.0 m2 g−1 and Vmicro = 0.01 cm3 g−1 for MCW(LD); SBET = 8.0 m2 g−1 and Vmicro = 0.01 cm3 g−1 for CAR-MCW(LD)). High oxygen content in MCW(PA)3h favoured the catalytic oxidation reaction of H2S, promoting its removal. The use of MCW as precursor and LD as activating agent of the ACs may contribute for the integrated management of maize wastes and to diversify the applications of anaerobic digestate.

Figueira, J, Loureiro J, Marques J, Bianchi C, Duarte P, Ruoho M, Tittonen I, Ferreira I.  2017.  Optimization of Cuprous Oxides Thin Films to be used as Thermoelectric Touch Detectors. ACS Applied Materials & Interfaces. 9:6520-6529., Number 7 AbstractWebsite

The electronic and optical properties of p-type copper oxides (CO) strongly depend on the production technique as it influences the obtained phases: cuprous oxide (Cu2O) or cupric oxide (CuO), the most common ones. Cu films deposited by thermal evaporation have been annealed in air atmosphere, with temperature between 225 and 375 °C and time between 1 and 4 h. The resultant CO films have been studied to understand the influence of processing parameters in the thermoelectric, electrical, optical, morphological, and structural properties. Films with a Cu2O single phase are formed when annealing at 225 °C, while CuO single phase films can be obtained at 375 °C. In between, both phases are obtained in proportions that depend on the film thickness and annealing time. The positive sign of the Seebeck coefficient (S), measured at room temperature (RT), confirms the p-type behavior of both oxides, showing values up to 1.2 mV·°C–1 and conductivity up to 2.9 (Ω·m)−1. A simple detector using Cu2O have been fabricated and tested with fast finger touch events.

Bernardo, M, Correa CR, Ringelspacher Y, Becker GC, Lapa N, Fonseca I, Esteves IAAC, Kruse A.  2020.  Porous carbons derived from hydrothermally treated biogas digestate. Waste Management. 105:170-179. AbstractWebsite

Porous carbons from digestate-derived hydrochar were produced, characterized and their performance to reclaim phosphate from water was evaluated as a preliminary approach to demonstrate their practical application. In a first step, the digestate was converted into hydrochars through hydrothermal carbonization by using two different pH conditions: 8.3 (native conditions) and 3.0 (addition of H2SO4). The resulting hydrochars did not present significant differences. Consecutively, the hydrochars were activated with KOH to produce activated carbons with enhanced textural properties. The resulting porous carbons presented marked differences: the AC native presented a lower ash content (20.3 wt%) and a higher surface area (SBET = 1106 m2/g) when compared with the AC-H2SO4 (ash content = 43.7 wt% SBET = 503 m2/g). Phosphorus, as phosphate, is a resource present in significative amount in wastewater, causing serious problems of eutrophication. Therefore, the performance of the porous carbons samples to recover phosphate – P(PO43−) – from water was evaluated through exploitation assays that included kinetic studies. The lumped model presented a good fitting to the kinetic data and the obtained uptake capacities were the same for both carbons, 12 mg P(PO43−)/g carbon. Despite the poorer textural properties of AC-H2SO4, this carbon was richer in Ca, Al, Fe, K, and Mg cations which promoted the formation of mineral complexes with phosphate anions. The results obtained in this work are promising for the future development of P(PO43−) enriched carbons that can be used thereafter as biofertilizers in soil amendment applications.

Dias, D, Lapa N, Bernardo M, Godinho D, Fonseca I, Miranda M, Pinto F, Lemos F.  2017.  Properties of chars from the gasification and pyrolysis of rice waste streams towards their valorisation as adsorbent materials. Waste Management. 65:186-194. AbstractWebsite

Rice straw (RS), rice husk (RH) and polyethylene (PE) were blended and submitted to gasification and pyrolysis processes. The chars obtained were submitted to textural, chemical, and ecotoxic characterisations, towards their possible valorisation. Gasification chars were mainly composed of ashes (73.4–89.8wt%), while pyrolysis chars were mainly composed of carbon (53.0–57.6wt%). Silicon (Si) was the major mineral element in all chars followed by alkaline and alkaline-earth metal species (AAEMs). In the pyrolysis chars, titanium (Ti) was also a major element, as the feedstock blends contained high fractions of PE which was the main source of Ti. Gasification chars showed higher surface areas (26.9–62.9m2g−1) and some microporosity, attributed to porous silica. On the contrary, pyrolysis chars did not present a porous matrix, mainly due to their high volatile matter content. The gasification bed char produced with 100% RH, at 850°C, with O2 as gasification agent, was selected for further characterization. This char presented the higher potential to be valorised as adsorbent material (higher surface area, higher content of metal cations with exchangeable capacity, and lowest concentrations of toxic heavy metals). The char was submitted to an aqueous leaching test to assess the mobility of chemical species and the ecotoxic level for V. fischeri. It was observed that metallic elements were significantly retained in the char, which was attributed mainly to its alkaline character. This alkaline condition promoted some ecotoxicity level on the char eluate that was eliminated after the pH correction.

Godinho, D, Nogueira M, Bernardo M, Dias D, Lapa N, Fonseca I, Pinto F.  2019.  Recovery of Cr(III) by using chars from the co-gasification of agriculture and forestry wastes, Aug. Environmental Science and Pollution Research. 26:22723–22735., Number 22 AbstractWebsite

The aim of the present work was to assess the efficiency of biochars obtained from the co-gasification of blends of rice huskþinspace}+þinspace}corn cob (biochar 50CC) and rice huskþinspace}+þinspace}eucalyptus stumps (biochar 50ES), as potential renewable low-cost adsorbents for Cr(III) recovery from wastewaters. The two gasification biochars presented a weak porous structure (ABETþinspace}=þinspace}63–144 m2 g−1), but a strong alkaline character, promoted by a high content of mineral matter (59.8{%} w/w of ashes for 50CC biochar and 81.9{%} w/w for 50ES biochar). The biochars were used for Cr(III) recovery from synthetic solutions by varying the initial pH value (3, 4, and 5), liquid/solid (L/S) ratio (100–500 mL g−1), contact time (1–120 h), and initial Cr(III) concentration (10–150 mg L−1). High Cr(III) removal percentages (around 100{%}) were obtained for both biochars, due to Cr precipitation, at low L/S ratios (100 and 200 mL g−1), for the initial pH 5 and initial Cr concentration of 50 mg L−1. Under the experimental conditions in which other removal mechanisms rather than precipitation occurred, a higher removal percentage (49.9{%}) and the highest uptake capacity (6.87 mg g−1) were registered for 50CC biochar. In the equilibrium, 50ES biochar presented a Cr(III) removal percentage of 27{%} with a maximum uptake capacity of 2.58 mg g−1. The better performance on Cr(III) recovery for the biochar 50CC was attributed to its better textural properties, as well as its higher cation exchange capacity.

Sharipova, AA, Aidarova SB, Bekturganova NY, Tleuova A, Kerimkulova M, Yessimova O, Kairaliyeva T, Lygina O, Lyubchik S, Miller R.  2017.  Triclosan adsorption from model system by mineral sorbent diatomite. Colloids and Surfaces A: Physicochemical and Engineering Aspects. 532:97-101. AbstractWebsite

Adsorption of model systems of triclosan by mineral sorbent diatomite is studied. The triclosan equilibrium concentration was measured spectrophotometrically, the morphology of the diatomite characterized using scanning electron microscopy and the amount of the adsorbed triclosan on the diatomite quantified by a mass balance. Adsorption isotherms were analyzed according to the linear/nonlinear form of Langmuir, Freundlich, Sips and Toth isotherm models isotherms, using AMPL software. It is shown that nonlinear Langmuir and Sips isotherm model provided suitable fitting results and no pronounced difference in adsorption efficiency between isotherms measured after 1, 2 and 3days adsorption was observed. Determined maximum adsorption capacity of diatomite towards triclosan qs is 140mg/g. Averaged calculated values of ΔG are −9.9 and −9.6kJ/mol for Langmuir and Sips models respectively. The negative sign of such values indicates spontaneous, physical in nature adsorption.

Sharipova, AA, Aidarova SB, Bekturganova NE, Tleuova A, Schenderlein M, Lygina O, Lyubchik S, Miller R.  2016.  Triclosan as model system for the adsorption on recycled adsorbent materials. Colloids and Surfaces A: Physicochemical and Engineering Aspects. 505:193-196. AbstractWebsite

The adsorption of triclosan as model system was studied to qualify activated carbon sorbents recycled from gas masks (civilian gas mask GP5). The triclosan equilibrium concentration was measured spectrophotometrically, the morphology of the activated carbon characterized by scanning electron microscopy, and the amount of the adsorbed triclosan on the activated carbon quantified by a mass balance method. Experimental isotherms were fitted by Langmuir, Freundlich and Sips adsorption models. It was obtained that the contact time is a crucial sorption parameter that provides information on the optimum adsorption efficiency. It was shown that the maximum efficiency of GP5 (88%) is obtained after 10days of adsorption at a maximal concentration of triclosan and carbon loading 1mg/l. No significant adsorption efficiency differences were measured after 5 and 10days of adsorption. The non-linear Sips isotherm, a combined Freundlich–Langmuir model, provides suitable fitting results. The observed remarkable adsorption capacity of activated carbon (GP5) towards triclosan adsorption (∼85mg/g) makes it a viable solution for wastewater treatment.

Lourenço, SC, Torres CAV, Nunes D, Duarte P, Freitas F, Reis MAM, Fortunato E, Moldão-Martins M, da Costa LB, Alves VD.  2017.  Using a bacterial fucose-rich polysaccharide as encapsulation material of bioactive compounds. International Journal of Biological Macromolecules. 104:1099-1106. AbstractWebsite

The potential of a bacterial exopolysaccharide named FucoPol, produced by the bacterium Enterobacter A47, as encapsulation matrix was explored. Spherical capsules with a smooth surface were produced by spray drying. The obtained microcapsules had average diameters ranging from 0.5 to 26.7μm and presented thin walls (thickness from 222 to 1094nm). The capsules were loaded with two bioactive compounds: gallic acid (GA) and oregano essential oil (OEO). Both bioactive materials were encapsulated in FucoPol particles, retaining their antioxidant activity after the drying process. Release studies showed that GA release in simulated gastric and intestinal fluids was faster than that of OEO, envisaging that the latter had established stronger interactions with the polymer matrix. These results suggest that FucoPol has a good potential for use as encapsulating material of bioactive compounds for application in several areas, including food, cosmetic or pharmaceutical products.

Bianchi, C, Ferreira LM, Loureiro J, Rodrigues A, Duarte P, Baptista AC, Ferreira IM.  2016.  Vanadium Pentoxide Alloyed with Graphite for Thin-Film Thermal Sensors, Mar. Journal of Electronic Materials. 45:1987–1991., Number 3 AbstractWebsite

The thermoelectric (TE) properties of vanadium pentoxide (V2O5) alloyed with graphite (G) were studied as a function of its incorporation percentage. Variable weight percentages of graphite powder (0–50{%}) were added to V2O5 powder and their mixtures were evaporated by a thermal evaporation technique to form thin films with a thickness in the range of 30–80 nm. In the infrared wavelength region, the transmittance of the obtained films increased as the G percentage was increased, while in the visible range, it decreased with G up to 10{%}. The TE properties were improved when G was in the range of 10–30{%}, while it decreased for the other percentages: Seebeck coefficient (S) changed from 0.6 mV/K to 0.9 mV/K and was zero with a G of 50{%}; the electrical conductivity varied slightly from 5 ($Ømega$m)−1 to 0.7 ($Ømega$m)−1 while the mobility improved from 0.07 cm2/V s to 1.5 cm2/V s and the respective carrier concentration was reduced, from 1 × 1018 cm−3 to 4 × 1016 cm−3. These films were applied as temperature sensors evaluating the thermovoltage as a function of thermal gradient between two electrodes, in which one was maintained at room temperature.

Book Chapter
Lyubchik, S, Lygina E, Lyubchyk A, Lyubchik S, Loureiro JM, Fonseca IM, Ribeiro AB, Pinto MM, Figueiredo AMSá.  2016.  The Kinetic Parameters Evaluation for the Adsorption Processes at ``Liquid–Solid'' Interface. Electrokinetics Across Disciplines and Continents: New Strategies for Sustainable Development. (Ribeiro, Alexandra B., Mateus, Eduardo P., Couto, Nazaré, Eds.).:81–109., Cham: Springer International Publishing Abstract

The kinetic parameters of the adsorption process at ``liquid–solid'' interface have been evaluated through the sets of time-based experiments of the Cr(III) adsorption under varying temperature, initial metal concentration, and carbon loading for two sets of the commercially available activated carbons and their post-oxidized forms with different texture and surface functionality.