Publications

Export 7 results:
Sort by: Author [ Title  (Asc)] Type Year
A B C D E F G H I J K L M N O P Q R [S] T U V W X Y Z   [Show ALL]
S
João, Carlos, Rute Almeida, Jorge Carvalho Silva, and João Paulo Borges. "A simple sol-gel route to the construction of hydroxyapatite inverted colloidal crystals for bone tissue engineering." Materials Letters 185 (2016): 407-410. AbstractWebsite

Hydroxyapatite (HAp) scaffolds with uniform pore size and interconnected pore network were constructed based on the inverted colloidal crystal (ICC) geometry and a simple sol-gel formulation. Monodisperse polystyrene microspheres were self-assembled and annealed into a hexagonal close packed structure. HAp sol-gel was infiltrated in this template followed by thermal treatment for simultaneous HAp matrix sintering and polymeric colloidal crystal calcination. The resultant ICC scaffolds exhibit an ordered architecture that was able to offer a favorable environment for human osteoblasts adhesion and proliferation, an essential feature for bone ingrowth in tissue engineering applications.

Neagu, Eugene, Maria Carmo Lança, Carlos Dias, and José Marat-Mendes. "Space charge and dipolar charge contribution at polar polymers polarization." IEEE Transactions on Dielectrics and Electrical Insulation 22 (2015): 1419-1426. AbstractWebsite

The thermally stimulated discharge current, the final thermally stimulated discharge current, DC conductivity and the final thermally stimulated discharge current with partially blocking electrode measures were used to analyze electrical behavior of Nylon 11. The objective was to discriminate between dipole related effects and space charge related effects. The space charge effects are dominant in the temperature range from room temperature to 170 °C. By using a Teflon-FEP partially blocking electrode, the space charge injected in the sample is diminished and the effects related to dipole movement can be observed. Beside the two known relaxations for Nylon 11, one associated with the glass transition around 60 °C and a second one associated with a molecular motion in the rigid-amorphous phase at 96 °C, a weak relaxation was observed around 168 °C. The peak around 96 °C is quite broad been composed of two narrow peaks. The final thermally stimulated discharge current method allows a better selection of the experimental conditions for sample charging (polarization) to have only a partial overlap between the nearby peaks. The peak's maximum current and temperature are dependent on the ratio between the charging and discharging time and temperature given a possibility to discriminate between dipolar and space charge effects. A pyroelectric current changes sign around 140 °C indicating that the amidegroup dipoles are frozen in opposite directions when the sample temperature is below 140 °C (amorphous and rigid-amorphous phase) or above (crystalline phase). The conductivity is controlled by the competition between n(E,T) and μ(E,T) indicating a space charge controlled conductivity mechanism.

Ferreira, Isabel, Ana Catarina Baptista, Joaquim Pratas Leitão, Jorge Soares, Elvira Fortunato, Rodrigo Martins, and João Paulo Borges. "Strongly Photosensitive and Fluorescent F8T2 Electrospun Fibers." Macromol Mater Eng 298 (2013): 174-180. AbstractWebsite

Electrospun fibers of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-bithiophene] (F8T2) with exceptional electro-optical performance are obtained. The I/T characteristics measured in fibers with 7–15 µm diameter and 1 mm length show a semiconductor behavior; their thermal activation energy is 0.5 eV and the dark conductivity at RT is 5 × 10−9 (Ω cm)−1. Besides exhibiting a photosensitivity of about 60 under white light illumination with a light power intensity of 25 mW · cm−2, the fibers also attain RT photoluminescence in the cyan, yellow, and red wavelength range under ultraviolet, blue, and green light excitation, respectively. Optical microscope images of F8T2 reveal homogeneous electrospun fibers, which are in good agreement with the uniformly radial fluorescence observed.

Chaparro, Catarina IP, Liliana R. Loureiro, Manuel Almeida Valente, Paula A. Videira, João Paulo Borges, and Paula I. P. Soares. "Synthesis and Characterization of Magnetic Nanoparticles and their internalization on Tumor Cell Lines." 2019 IEEE 6th Portuguese Meeting on Bioengineering (ENBENG) (2019): 1-4. AbstractWebsite

Truncated sialylated O-glycans, such as cell-surface carbohydrate antigen sialyl-Tn (STn) are overexpressed by several cancer types, but not by the respective normal tissues. STn expression is associated with oncogenesis and metastatic ability of cancer cells, with reduced overall survival and lack of response to chemotherapy. Advances in nanomedicine have resulted in rapid development of biocompatible superparamagnetic iron oxide nanoparticles (SPIONs) with considerable potential in cancer treatment. Therefore, in this study SPIONs coated with oleic acid (OA) or dimercaptosuccinic acid (DMSA) were developed and characterized for internalization in two breast cancer cell lines: cell line expressing the STn antigen and the corresponding control. SPIONs with an average diameter of 8 nm showed superparamagnetic behavior and high potential to be used as magnetic hyperthermia agents. OA and DMSA coating provided high stability of SPIONs in physiological conditions while not changing their main properties. NPs internalization studies showed a higher accumulation of DMSA coated NPs in the breast cancer MDA-MB-231 WT cell line. In MDA-MB-231 cell line expressing STn both coated NPs showed a similar accumulation. Therefore, STn antigen can act as a receptor capable of detecting and covalently bind to the molecules present on NPs surface and induce their cellular uptake by endocytosis.

Marques, Ana, Davide Miglietta, G. Gaspar, Ana Catarina Baptista, A. Gaspar, P. Perdigão, Iris Soares, Catarina Bianchi, David Sousa, Bruno Morais M. Faustino, V. S. Amaral, T. Santos, A. P. Gonçalves, R. C. da Silva, Fabrizio Giorgis, and Isabel Ferreira. "Synthesis of thermoelectric magnesium-silicide pastes for 3D printing, electrospinning and low-pressure spray." Materials for Renewable and Sustainable Energy 8 (2019): 21. AbstractWebsite

In this work, eco-friendly magnesium-silicide (Mg2Si) semiconducting (n-type) thermoelectric pastes for building components concerning energy-harvesting devices through 3D printing, spray and electrospinning were synthetized and tested for the first time. The Mg2Si fine powders were obtained through the combination of ball milling and thermal annealing under Ar atmosphere. While the latter process was crucial for obtaining the desired Mg2Si phase, the ball milling was indispensable for homogenizing and reducing the grain size of the powders. The synthetized Mg2Si powders exhibited a large Seebeck coefficient of ~ 487 µV/K and were blended with a polymeric solution in different mass ratios to adjust the paste viscosity to the different requirements of 3D printing, electrospinning and low-pressure spray. The materials produced in every single stage of the paste synthesis were characterized by a variety of techniques that unequivocally prove their viability for producing thermoelectric parts and components. These can certainly trigger further research and development in green thermoelectric generators (TEGs) capable of adopting any form or shape with enhanced thermoelectric properties. These green TEGs are meant to compete with common toxic materials such as Bi2Te3, PbTe and CoSb that have Seebeck coefficients in the range of ~ 290–700 μV/K, similar to that of the produced Mg2Si powders and lower than that of 3D printed bulk Mg2Si pieces, measured to be ~ 4866 μV/K. Also, their measured thermal conductivities proved to be significantly lower (~ 0.2 W/mK) than that reported for Mg2Si (≥ 4 W/mK). However, it is herein demonstrated that such thermoelectric properties are not stable over time. Pressureless sintering proved to be indispensable, but difficultly achievable by long thermal annealing (even above 32 h) in inert atmosphere at 400 °C, at least for bulk Mg2Si pieces constituted by a mean grain size of 2–3 μm. Hence, for overcoming this sintering challenge and become the silicide’s extrusion viable in the production of bulk thermoelectric parts, alternative pressureless sintering methods will have to be further explored.

Vieira, Tânia, Jorge Carvalho Silva, João Paulo Borges, and Célia Henriques. "Synthesis, electrospinning and in vitro test of a new biodegradable gelatin-based poly(ester urethane urea) for soft tissue engineering." European Polymer Journal 103 (2018): 271-281. AbstractWebsite

Biodegradable polyurethanes have been studied as scaffolds for tissue engineering due to their adjustable physico-chemical properties. In this work, we synthesized a biodegradable gelatin-based poly(urethane urea) using polycaprolactone-diol, as soft segment, and isophorone diisocyanate and gelatin from cold water fish skin as hard segment. The synthesis was confirmed by Fourier transform infrared spectroscopy and proton nuclear magnetic resonance and the influence of the amount of gelatin introduced in the polymer backbone was analyzed by thermal analysis. Gelatin-based poly(urethane urea) electrospun fibrous mats and solvent cast films were then produced and their physico-chemical and biological properties studied. They present an amorphous structure, elastomeric behavior and water contact angles typical of hydrophobic surfaces. Hydrolytic degradation was analyzed in phosphate buffer saline (PBS), lipase and trypsin solutions. No mass changes were detected during 37 days in PBS and trypsin while significant degradation by lipase was observed. Human foetal foreskin fibroblasts were seeded on the fibrous mats and films. Populations were evaluated by colorimetric cell viability assays and morphology by fluorescence imaging. The substrates supported cell adhesion and proliferation. The novel gelatin-based poly(urethane urea) fibrous mats offer attractive physico-chemical and biological properties for soft tissue engineering applications.

Henriques, Célia, Ricardo Vidinha, David Botequim, João Paulo Borges, and Jorge Carvalho Silva. "A systematic study of solution and processing parameters on nanofiber morphology using a new electrospinning apparatus." Journal of nanoscience and nanotechnology 9 (2009): 3535-3545. AbstractWebsite

We assembled a new electrospinning apparatus and used poly(ethylene oxide) as a model polymer to perform a systematic study on the influence of solution and processing parameters on the morphology of electrospun nanofibers. Solution parameters studied were polymer concentration and molecular mass. The solvent used, 60 wt% water,40 wt% ethanol, was the same throughout the study. Processing parameters analyzed were: solution feed rate, needle tip-collector distance and electrostatic potential difference between the needle and collector. Solution viscosity increased both with polymer concentration and molecular mass. Polymer concentration plays a decisive role on the outcome of the electrospinning process: a low concentration led to the formation of beaded fibers; an intermediate concentration yielded good quality fibers; a high concentration resulted in a bimodal size distribution and at even higher concentration a distributed deposition. Fiber diameter increased with polymer molecular mass and higher molecular masses are associated with a higher frequency of splaying events. Fiber diameter increased linearly with solution feed rate. While an increase in needle-collector distance represents a weaker electric field, a greater distance to be covered by the fibers and a longer flight time, presumably favoring the formation of thinner fibers, as solvent evaporation leads to a local increase of concentration and viscosity, viscoelastic forces opposing stretching caused an increase of fiber diameter with needle-collector distance. A higher voltage applied at the needle is associated with a higher charging of the polymer and a higher electrical current through it ultimately leading to incomplete solvent evaporation and merged fibers being produced. Controlling the charging of the polymer independently of the electric field strength was achieved by applying a voltage to the collector while distance and potential difference were kept constant. The increased electrostatic repulsion associated with an increase of the high voltage applied to the needle led to the disappearance of merged fibers.