Machado, MA, Antin K-N, Rosado LS, Vilaça P, Santos TG.
2019.
Contactless high-speed eddy current inspection of unidirectional carbon fiber reinforced polymer. Composites Part B: Engineering. 168:226-235.
AbstractThis paper presents the development and the results of a customized eddy current (EC) non-destructive testing (NDT) system for highly demanding online inspection conditions. Several planar eddy current array probes were designed, numerically simulated and experimentally compared for the inspection of low conductivity unidirectional carbon fibre reinforced polymer (CFRP) ropes. The inspections were performed using a dedicated scanner device at 4 m/s with 3 mm probe lift-off where defects under 1 mm were detected with an excellent SNR. Different defect morphologies and sizes, such as broken fibres and lateral cuts, were successful detected and compared to conventional probes.
Esteves C, Santos GMC, Alves C, Palma S, Porteira AR, Filho J, HA C, Alves VD, Faustino BMM, Ferreira I, Gamboa H, Roque ACA.
2019.
Effect of film thickness in gelatin hybrid gels for artificial olfaction. Materials Today Bio. 1:-.
AbstractArtificial olfaction is a fast-growing field aiming to mimic natural olfactory systems. Olfactory systems rely on a first step of molecular recognition in which volatile organic compounds (VOCs) bind to an array of specialized olfactory proteins. This results in electrical signals transduced to the brain where pattern recognition is performed. An efficient approach in artificial olfaction combines gas-sensitive materials with dedicated signal processing and classification tools. In this work, films of gelatin hybrid gels with a single composition that change their optical properties upon binding to VOCs were studied as gas-sensing materials in a custom-built electronic nose. The effect of films thickness was studied by acquiring signals from gelatin hybrid gel films with thicknesses between 15 and 90 μm when exposed to 11 distinct VOCs. Several features were extracted from the signals obtained and then used to implement a dedicated automatic classifier based on support vector machines for data processing. As an optical signature could be associated to each VOC, the developed algorithms classified 11 distinct VOCs with high accuracy and precision (higher than 98%), in particular when using optical signals from a single film composition with 30 μm thickness. This shows an unprecedented example of soft matter in artificial olfaction, in which a single gelatin hybrid gel, and not an array of sensing materials, can provide enough information to accurately classify VOCs with small structural and functional differences.
Esteves, C, Santos GMC, Alves C, Palma SICJ, Porteira AR, Costa HMA, Alves VD, Faustino BMM, Ferreira I, Gamboa H.
2019.
Effect of film thickness in gelatine hybrid gels for artificial olfaction. Materials Today Bio. 1:100002.
Antin, K-N, Machado MA, Santos TG, Vilaça P.
2019.
Evaluation of Different Non-destructive Testing Methods to Detect Imperfections in Unidirectional Carbon Fiber Composite Ropes. Journal of Nondestructive Evaluation. 38(23)
AbstractOnline monitoring of carbon fiber reinforced plastic (CFRP) ropes requires non-destructive testing (NDT) methods capable of detecting multiple damage types at high inspection speeds. Three NDT methods are evaluated on artificial and realistic imperfections in order to assess their suitability for online monitoring of CFRP ropes. To support testing, the microstructure and electrical conductivity of a carbon fiber rope is characterized. The compared methods are thermography via thermoelastic stress analysis, ultrasonic testing with commercial phased array transducers, and eddy current testing, supported by tailor-made probes. While thermoelastic stress analysis and ultrasonics proved to be accurate methods for detecting damage size and the shape of defects, they were found to be unsuitable for high-speed inspection of a CFRP rope. Instead, contactless inspection using eddy currents is a promising solution for real-time online monitoring of CFRP ropes at high inspection speeds.
Khili, F, Borges JB, Almeida PL, Boukherroub R, Omrani AD.
2019.
Extraction of Cellulose Nanocrystals with Structure I and II and Their Applications for Reduction of Graphene Oxide and Nanocomposite Elaboration. Waste and Biomass Valorization. 10:1913-1927.
AbstractThe aim of the present study is to investigate the effect of the hydrolysis process on the properties of nanocrystalline cellulose (NCC) isolated from different precursors and the subsequent use of the extracted NCC for the reduction of graphene oxide (GO). The raw materials (almond and peanut shells) chosen for the isolation of cellulose were selected on the basis of their abundance and their poorly investigation in the production of NCC. Microcrystalline cellulose (MCC) was firstly extracted by alkali and bleaching treatments, then hydrolyzed under different processes to produce NCC polymorphs with structure I (NCC-I) and NCC structure II (NCC-II). The Fourier transform infrared spectroscopy, the X-ray diffraction (XRD) and the 13C NMR studies of the alkali and bleached products confirmed the formation of cellulose type I with high purity and good crystallinity, while scanning electron microscopy (SEM) showed micrometric fibers with lengths reaching 80 µm. Sulfuric acid treatment of these microfibers results in NCC type I or II, depending on the hydrolysis process. SEM of the NCC samples exhibited nanorods with diameter and aspect ratio in the range of 20–40 and 20–25 nm, respectively. Thermogravimetric analysis (TGA) of the MCC and NCC products indicated stable materials with a degradation temperature reaching 240 and 200 °C for MCC and NCC, respectively. The other part of our work concerns the use of the obtained cellulose nanocrystals (type II) for the preparation of reduced graphene oxide composite (NCC/RGO), to demonstrate the reducing properties of the isolated NCCII.
Khili, F, Borges J, Almeida PL, Boukherroub R, Omrani AD.
2019.
Extraction of Cellulose Nanocrystals with Structure I and II and Their Applications for Reduction of Graphene Oxide and Nanocomposite Elaboration. Waste and Biomass Valorization. 10:1913–1927.
AbstractThe aim of the present study is to investigate the effect of the hydrolysis process on the properties of nanocrystalline cellulose (NCC) isolated from different precursors and the subsequent use of the extracted NCC for the reduction of graphene oxide (GO). The raw materials (almond and peanut shells) chosen for the isolation of cellulose were selected on the basis of their abundance and their poorly investigation in the production of NCC. Microcrystalline cellulose (MCC) was firstly extracted by alkali and bleaching treatments, then hydrolyzed under different processes to produce NCC polymorphs with structure I (NCC-I) and NCC structure II (NCC-II). The Fourier transform infrared spectroscopy, the X-ray diffraction (XRD) and the 13C NMR studies of the alkali and bleached products confirmed the formation of cellulose type I with high purity and good crystallinity, while scanning electron microscopy (SEM) showed micrometric fibers with lengths reaching 80 µm. Sulfuric acid treatment of these microfibers results in NCC type I or II, depending on the hydrolysis process. SEM of the NCC samples exhibited nanorods with diameter and aspect ratio in the range of 20–40 and 20–25 nm, respectively. Thermogravimetric analysis (TGA) of the MCC and NCC products indicated stable materials with a degradation temperature reaching 240 and 200 °C for MCC and NCC, respectively. The other part of our work concerns the use of the obtained cellulose nanocrystals (type II) for the preparation of reduced graphene oxide composite (NCC/RGO), to demonstrate the reducing properties of the isolated NCCII.
Machado, MA, Antin KN, Rosado LS, Vilaça P, Santos TG.
2019.
High speed inspection of UD CFRP composites. 58th Annual Conference of the British Institute of Non-Destructive Testing, NDT 2019. , Telford, UK
AbstractOnline monitoring of carbon fibre reinforced polymer (CFRP) components requires a Non-Destructive Testing (NDT) method capable of contactless sensing of damage, while enabling high inspection speeds needed for monitoring large components. Eddy current testing (ECT) of CFRP components has great potential for two reasons. First, ECT probes are capable of operating without contact, although minimizing the lift-off is preferred. Second, impedance analysers with high sample rates make high-speed inspection possible. This research assesses the damage detection capabilities of eddy current probes on CFRP samples with artificial and realistic damage. To support the aptitude of the ECT method for these needs, the CFRP material is characterized and numerical simulations are performed in order to develop optimized and tailored ECT probes for the detection of defects with different morphologies, namely fibre breakage and delaminations, and to take into consideration the highly anisotropic electrical bulk resistivity of the CFRP material. Different ECT probes were designed, produced and experimentally validated. The experiments were performed at a high inspection speed (4 m/s) and the high sensitivity of the probes was demonstrated.
Kourmentza, C, Araujo D, Sevrinc C, Roma-Rodriques C, Ferreira LJ, Freitas F, Dionísio M, Baptista PV, Fernandes AR, Grandfils C, Reis MAM.
2019.
Occurrence of non-toxic bioemulsifiers during polyhydroxyalkanoate production by Pseudomonas strains valorizing crude glycerol by-product. Bioresource Technology . 281:31-40.
Paiva, T, Echeverria C, Godinho MH, Almeida PL, Corvo M.
2019.
On the influence of imidazolium ionic liquids on cellulose derived polymers. European Polymer Journal. : Elsevier
AbstractThe demand for better cellulose solvents has driven the search for new and improved materials to enable the processing of this polysaccharide. Ionic liquids have been debated for a long time as interesting alternatives, but the molecular details on the solubilization mechanism have been a matter of controversy. Herein, for the first time, the structure and dynamics of hydroxypropylcellulose (HPC) liquid crystal solutions were probed in the presence of imidazolium ionic liquids (ILs), conjugating rheological measurements with magnetic resonance spectroscopy. This study provides a characterization of the solutions macroscopic behaviour, where the liquid crystalline (LC) properties were maintained. Using ILs with different side chain lengths, the influence of the hydrophobic IL domain in the solvation abilities of ILs towards a cellulose derived polymer was accessed, providing experimental evidence on these interactions.
Santos, G, Alves C, Pádua AC, Palma S, Gamboa H, Roque ACA.
2019.
An Optimized E-nose for Efficient Volatile Sensing and Discrimination. Proceedings of the 12th International Joint Conference on Biomedical Engineering Systems and Technologies - Volume 1: BIODEVICES. , Prague, Czech Republic
AbstractElectronic noses (E-noses), are usually composed by an array of sensors with different selectivities towards classes of VOCs (Volatile Organic Compounds). These devices have been applied to a variety of fields, including environmental protection, public safety, food and beverage industries, cosmetics, and clinical diagnostics. This work demonstrates that it is possible to classify eleven VOCs from different chemical classes using a single gas sensing biomaterial that changes its optical properties in the presence of VOCs. To accomplish this, an in-house built E-nose, tailor-made for the novel class of gas sensing biomaterials, was improved and combined with powerful machine learning techniques. The device comprises a delivery system, a detection system and a data acquisition and control system. It was designed to be stable, miniaturized and easy-to-handle. The data collected was pre-processed and features and curve fitting parameters were extracted from the original response. A recursive feature selection method was applied to select the best features, and then a Support Vector Machine classifier was implemented to distinguish the eleven distinct VOCs. The results show that the followed methodology allowed the classification of all the VOCs tested with 94.6% (± 0.9%) accuracy.
Marques, A, Miglietta D, Gaspar G, Baptista AC, Gaspar A, Perdigão P, Soares I, Bianchi C, Sousa D, Faustino BMM, Amaral VS, Santos T, Gonçalves AP, da Silva RC, Giorgis F, Ferreira I.
2019.
Synthesis of thermoelectric magnesium-silicide pastes for 3D printing, electrospinning and low-pressure spray. Materials for Renewable and Sustainable Energy. 8:21.
AbstractIn this work, eco-friendly magnesium-silicide (Mg2Si) semiconducting (n-type) thermoelectric pastes for building components concerning energy-harvesting devices through 3D printing, spray and electrospinning were synthetized and tested for the first time. The Mg2Si fine powders were obtained through the combination of ball milling and thermal annealing under Ar atmosphere. While the latter process was crucial for obtaining the desired Mg2Si phase, the ball milling was indispensable for homogenizing and reducing the grain size of the powders. The synthetized Mg2Si powders exhibited a large Seebeck coefficient of ~ 487 µV/K and were blended with a polymeric solution in different mass ratios to adjust the paste viscosity to the different requirements of 3D printing, electrospinning and low-pressure spray. The materials produced in every single stage of the paste synthesis were characterized by a variety of techniques that unequivocally prove their viability for producing thermoelectric parts and components. These can certainly trigger further research and development in green thermoelectric generators (TEGs) capable of adopting any form or shape with enhanced thermoelectric properties. These green TEGs are meant to compete with common toxic materials such as Bi2Te3, PbTe and CoSb that have Seebeck coefficients in the range of ~ 290–700 μV/K, similar to that of the produced Mg2Si powders and lower than that of 3D printed bulk Mg2Si pieces, measured to be ~ 4866 μV/K. Also, their measured thermal conductivities proved to be significantly lower (~ 0.2 W/mK) than that reported for Mg2Si (≥ 4 W/mK). However, it is herein demonstrated that such thermoelectric properties are not stable over time. Pressureless sintering proved to be indispensable, but difficultly achievable by long thermal annealing (even above 32 h) in inert atmosphere at 400 °C, at least for bulk Mg2Si pieces constituted by a mean grain size of 2–3 μm. Hence, for overcoming this sintering challenge and become the silicide’s extrusion viable in the production of bulk thermoelectric parts, alternative pressureless sintering methods will have to be further explored.
Chapa, M, Alexandre MF, Mendes MJ, Águas H, Fortunato E, Martins R.
2019.
All-Thin-Film Perovskite/C–Si Four-Terminal Tandems: Interlayer and Intermediate Contacts Optimization. ACS Applied Energy Materials. 2:3979-3985., Number 6
AbstractCombined perovskite/crystalline-silicon four-terminal tandem solar cells promise >30% efficiencies. Here we propose all-thin-film double-junction architectures where high-bandgap perovskite top cells are coupled to ultrathin c-Si bottom cells enhanced with light trapping. A complete optoelectronic model of the devices was developed and applied to determine the optimal intermediate layers, which are paramount to maximize the cells’ photocurrent. It was ascertained that by replacing the transparent conductive oxides by grid-based metallic contacts in the intermediate positions, the parasitic absorption is lowered by 30%. Overall, a 29.2% efficiency is determined for ∼2 um thick tandems composed of the optimized interlayers and improved with Lambertian light trapping.
Alves-Barroco, C, Roma-Rodrigues C, Balasubramanian N, Aparecida Guimarães M, Ferreira-Carvalho BT, Muthukumaran J, Nunes D, Fortunato E, Martins R, Santos-Silva T, Figueiredo AMS, Fernandes AR, Santos-Sanches I.
2019.
Biofilm development and computational screening for new putative inhibitors of a homolog of the regulatory protein BrpA in Streptococcus dysgalactiae subsp. dysgalactiae. International Journal of Medical Microbiology. 309:169-181., Number 3
AbstractStreptococcus dysgalactiae subsp. dysgalactiae (SDSD), a Lancefield group C streptococci (GCS), is a frequent cause of bovine mastitis. This highly prevalent disease is the costliest in dairy industry. Adherence and biofilm production are important factors in streptoccocal pathogenesis. We have previously described the adhesion and internalization of SDSD isolates in human cells and now we describe the biofilm production capability of this bacterium. In this work we integrated microbiology, imaging and computational methods to evaluate the biofilm production capability of SDSD isolates; to assess the presence of biofilm regulatory protein BrpA homolog in the biofilm producers; and to predict a structural model of BrpA-like protein and its binding to putative inhibitors. Our results show that SDSD isolates form biofilms on abiotic surface such as glass (hydrophilic) and polystyrene (hydrophobic), with the strongest biofilm formation observed in glass. This ability was mainly associated with a proteinaceous extracellular matrix, confirmed by the dispersion of the biofilms after proteinase K and trypsin treatment. The biofilm formation in SDSD isolates was also confirmed by confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). Under SEM observation, VSD16 isolate formed cell aggregates during biofilm growth while VSD9 and VSD10 formed smooth and filmy layers. We show that brpA-like gene is present and expressed in SDSD biofilm-producing isolates and its expression levels correlated with the biofilm production capability, being more expressed in the late exponential phase of planktonic growth compared to biofilm growth. Fisetin, a known biofilm inhibitor and a putative BrpA binding molecule, dramatically inhibited biofilm formation by the SDSD isolates but did not affect planktonic growth, at the tested concentrations. Homology modeling was used to predict the 3D structure of BrpA-like protein. Using high throughput virtual screening and molecular docking, we selected five ligand molecules with strong binding affinity to the hydrophobic cleft of the protein, making them potential inhibitor candidates of the SDSD BrpA-like protein. These results warrant further investigations for developing novel strategies for SDSD anti-biofilm therapy.
Torrisi, G, Luis JS, Sanchez-Sobrado O, Raciti R, Mendes MJ, Águas H, Fortunato E, Martins R, Terrasi A.
2019.
Colloidal-structured metallic micro-grids: High performance transparent electrodes in the red and infrared range. Solar Energy Materials and Solar Cells. 197:7-12.
AbstractOne of the most promising approaches to produce industrial-compatible Transparent Conducting Materials (TCMs) with excellent characteristics is the fabrication of TCO/metal/TCO multilayers. In this article, we report on the electro-optical properties of a novel high-performing TCO/metal/TCO structure in which the intra-layer is a micro-structured metallic grid instead of a continuous thin film. The grid is obtained by evaporation of Ag through a mask of polystyrene colloidal micro-spheres deposited by the Langmuir-Blodgett method and partially dry-etched in plasma. IZO/Ag grid/IZO structures with different thicknesses and mesh dimensions have been fabricated, exhibiting excellent electrical characteristics (sheet resistance below 10 Ω/□) and particularly high optical transmittance in the near-infrared spectral region as compared to planar (unstructured) TCM multilayers. Numerical simulations were also used to highlight the role of the Ag mesh parameters on the electrical properties.
Ambrosi, E, Bartlett P, Berg AI, Brivio S, Burr G, Deswal S, Deuermeier J, Haga M-A, Kiazadeh A, Kissling G, Kozicki M, Foroutan-Nejad C, Gale E, Gonzalez-Velo Y, Goossens A, Goux L, Hasegawa T, Hilgenkamp H, Huang R, Ibrahim S, Ielmini D, Kenyon AJ, Kolosov V, Li Y, Majumdar S, Milano G, Prodromakis T, Raeishosseini N, Rana V, Ricciardi C, Santamaria M, Shluger A, Valov I, Waser R, Stanley Williams R, Wouters D, Yang Y, Zaffora A.
2019.
Electrochemical metallization ReRAMs (ECM) - Experiments and modelling: General discussion. Faraday Discussions. 213:115-120.
Abstractn/a
Pinto, CAM, Palomar T, Alves LC, da Silva SHM, Monteiro RC, Macedo MF, Vilarigues MG.
2019.
Fungal biodeterioration of stained-glass windows in monuments from Belém do Pará (Brazil). International Biodeterioration & Biodegradation. 138:106-113.
AbstractThe most prominent historical buildings in Belém do Pará (Northern Brazil) have modernist stained-glass windows, which were commissioned from Europe since the end of the 19th century. Some of them present biodegradation; however, there is no information about the microbial activity on them. The present work is focused on the biodeterioration by fungi on some of these Modern stained-glass windows. The fungal communities were collected, isolated and then identified by means of molecular methods. Additionally, a laboratory-based biodeterioration experiment was carried out to assess the fungal activity on replica glass samples with three different chemical compositions. The replica samples were inoculated with a four-fungal species mixture and incubated under optimal growth conditions for 5 months. Optical microscopy, μ-PIXE, SEM-EDS and FTIR-ATR were performed to evaluate the biodeterioration of the soda-lime silicate glasses. This multidisciplinary approach showed that the inoculated spores (Aspergillus arenarioides, Fusarium oxysporum, Hortaea werneckii, and Trichoderma longibrachiatum) were able to form substantial mycelia in all replica glass samples. The main alterations observed were small crystals, hyphae fingerprints and a slight decrease on the glass surface smoothness. Despite the aforementioned damages, the soda-lime silicate glass compositions showed high resistance against the inoculated fungal species.
Sanchez-Sobrado, O, Mendes MJ, Haque S, Mateus T, Aguas H, Fortunato E, Martins R.
2019.
Lightwave trapping in thin film solar cells with improved photonic-structured front contacts. J. Mater. Chem. C. 7:6456-6464.: The Royal Society of Chemistry
AbstractPhotonic microstructures placed at the topside of photovoltaic cells are currently one of the preferred light management solutions to obtain efficiency enhancement due to the increment of the optical absorption produced in the active medium of the devices. Herein{,} we present the results concerning a practical{,} low-cost and scalable approach to integrate metal-oxide based light trapping microstructures on the front contact of amorphous silicon thin film solar cells. A colloidal lithography method was used to pattern the wavelength-sized pyramidal-like features composing the structures{,} made of two different transparent materials{,} TiO2 and IZO{,} allowing the detailed study of the influence of their geometrical parameters on the optoelectronic properties of the devices. These top coating structures are deposited as a post-process after the solar cell fabrication{,} thus facilitating and broadening their industrial applicability. Measurements of the light absorption{,} external quantum efficiency and I–V curves revealed that the structured coatings provide strong broadband improvements in the generated current{,} due to the suppression of reflected light at short wavelengths and the increment of the optical path length of the longer wavelengths (via light scattering){,} within the amorphous silicon layer. As a result{,} in the four types of structures analyzed in this study{,} remarkable increments were achieved in the cells’ efficiencies (up to 14.4%) and generated currents (up to 21.5%){,} with respect to the flat reference cells.