Electronic noses (e-noses) mimic the complex biological olfactory system, usually including an array of gas sensors to act as the olfactory receptors and a trained computer with signal-processing and pattern recognition tools as the brain. In this work, a new stimuli-responsive material is shown, consisting of self-assembled droplets of liquid crystal and ionic liquid stabilised within a fish gelatin matrix. These materials change their opto/electrical properties upon contact with volatile organic compounds (VOCs). By using an in-house developed e-nose, these new gas-sensing films yield characteristic optical signals for VOCs from different chemical classes. A support vector machine classifier was implemented based on 12 features of the signals. The results show that the films are excellent identifying hydrocarbon VOCs (toluene, heptane and hexane) (95% accuracy) but lower performance was found to other VOCs, resulting in an overall 60.4% accuracy. Even though they are not reusable, these sustainable gas-sensing films are stable throughout time and reproducible, opening several opportunities for future optoelectronic devices and artificial olfaction systems.

The following dissertation studies the behavior of flat slabs when subjected to constant vertical loads and cyclic horizontal displacements, as a continuation of previous studies developed at FCT/UNL. The main focus of this research is to study the influence of flexural reinforcement on the seismic response of flat slabs. Therefore, three reinforced concrete flat slabs with varying flexural reinforcement ratio were tested, two having the same top reinforcement ratio of !=0,64% and one with !=1,34%. One of the specimens with lower longitudinal ratio was reinforced with studs as specific punching shear reinforcement. All slabs had overall dimensions of 4,15 × 1,85 × 0,15 m3 and a gravity shear ratio, ratio between the gravity load and the punching shear resistance, approximately equal to 55%. For a more complete analysis the results obtained were compared to two other specimens from previous experimental campaigns also conducted at FCT/UNL. These two slabs were designed with top flexural reinforcement ratio (!=0,96%) that lies between the two tested in this dissertation, one with no shear-reinforcement and the other with headed studs. Results showed that the reduction of flexural reinforcement resulted in a more ductile behavior of the specimens and in a higher drift capacity. The high flexural ratio added to one specimen improved the maximum unbalanced moment capacity but also made the slab fail in a more brittle mode. As expected, the specimen with shear headed studs supported the highest drifts and ended up not failing during this experimental campaign, reaching the test setup upper limit.

The behavior of flat slab – column connections under seismic-type loading is complex and not exhaustively studied. Among the many variables involved, this paper focuses on the influence of flexural reinforcement on the seismic performance of such connections. Three specimens were tested and analyzed in conjunction with two previously published specimens tested under similar conditions, under constant vertical loading and cyclic horizontal displacements, resulting in a total of five specimens. Among these specimens, the top flexural reinforcement varied from 0.64% to 1.34% and the approximate value of applied gravity shear ratio (GSR, equal to the ratio between the applied gravity load and the punching shear resistance) was around 55%. Two of the specimens (low and median reinforcement ratio) were also reinforced with headed studs against punching shear to study the unbalanced moment transfer capacity of the slab – column connections. The specimens are described and analyzed in detail. The results show that the performance under cyclic loading is affected by the amount of flexural reinforcement, even though GSR was almost the same for all specimens. It is shown that current code-based approaches for the estimation of unbalanced moment capacity, as well as drift capacity, are generally safe sided for the specimens under investigation but do not fully capture the trends observed in the experimental campaign.

Advances in concrete technology during the last decades have resulted in the development of materials with enhanced mechanical properties, such as High Strength Concrete (HSC), Fibre Reinforced Concrete (FRC) and Ultra-High Performance Fibre Reinforced Concrete (UHPFRC). The application of these materials in flat slabs, which are a popular structural solution in Reinforced Concrete (RC) buildings worldwide, has the potential of significantly reducing raw material consumption by enabling the design of slenderer and therefore lighter structures. However, flat slabs are susceptible to punching shear failure, which is a complex phenomenon that remains challenging, even though significant efforts have been made to experimentally study it. For advanced concrete materials (HSC, FRC and UHPFRC), the challenge is further accentuated by the continuous and rapid development of these materials. With the purpose of identifying and highlighting gaps in the published literature, a review of tests with HSC, FRC and UHPFRC slab-column connections in non-seismic and seismic loading applications is presented in this paper. It is shown that future research directions in this field include, among others, testing thicker slabs, HSC slabs with higher concrete compressive strength, HSC combined with FRC and several more cases related to seismic loading conditions.

This study describes for the first time the iron- and copper-mediated gelation of FucoPol, fucose-rich bacterial polysaccharide. The ability of FucoPol to gel in the presence of metal cations, including iron(III) and copper(II), was used for the preparation of hydrogel beads. Iron mediated the formation of stable and not cytotoxic gel beads, while copper resulted in fragile and cytotoxic ones. Copper-mediated beads coated with an iron-mediated gel layer were more stable and had reduced cytotoxicity. The resulting polymeric structures had differing morphology, physical properties and cytotoxicity, which support their use in several applications, including biomedicine, agriculture and bioremediation.

Two piano-stool iron(II) complexes bearing N-heterocyclic carbene ligands outfitted with acetamide- and amine-pendant arms [Cp*Fe(NHCR)(CO)I] {Cp* = η5-tetramethylcyclopentadienyl; R = CH2CONEt2 (3), (CH2)2NEt2 (4)}, have been prepared and fully characterized. Their catalytic activity in transfer hydrogenation (TH) of ketones using iPrOH as a hydrogen source and catalytic amounts of base (LiOtBu) has been explored, along with that of previously reported [CpFe(NHCR)(CO)I] {R = nBu (5), (CH2)2OH (6), Et (7), and (CH2)3OH (8)} complexes containing hydroxyl and nonfunctionalized alkyl arms. Complex 3 displayed the highest catalytic activity of the whole series 3–8, reaching a TOF50 value of 533 h–1. NMR monitoring of the stoichiometric reaction of 3 with LiOtBu, allowed the identification of a new species 3' containing a deprotonated amidate moiety, which has been fully characterized by 1H, 13C, and 15N NMR. Finally, a green protocol for the reduction of ketones through TH using glycerol as a hydrogen source, under microwave irradiation in the presence of catalytic amounts of 3 and base has been developed.

Background: The STEAP1 is a cell-surface antigen over-expressed in prostate cancer, which contributes to tumor progression and aggressiveness. However, the molecular mechanisms underlying STEAP1 and its structural determinants remain elusive. Methods: The fraction capacity of Butyl- and Octyl-Sepharose matrices on LNCaP lysates was evaluated by manipulating the ionic strength of binding and elution phases, followed by a Co-Immunoprecipitation (Co-IP) polishing. Several potential stabilizing additives were assessed, and the melting temperature (Tm) values ranked the best/worst compounds. The secondary structure of STEAP1 was identified by circular dichroism. Results: The STEAP1 was not fully captured with 1.375 M (Butyl), in contrast with interfering heterologous proteins, which were strongly retained and mostly eluted with water. This single step demonstrated higher selectivity of Butyl-Sepharose for host impurities removal from injected crude samples. Co-IP allowed recovering a purified fraction of STEAP1 and contributed to unveil potential physiologically interacting counterparts with the target. A Tm of  55 °C was determined, confirming STEAP1 stability in the purification buffer. A predominant α-helical structure was identified, ensuring the protein’s structural stability. Conclusions: A method for successfully isolating human STEAP1 from LNCaP cells was provided, avoiding the use of detergents to achieve stability, even outside a membrane-mimicking environment.

After more than one hundred and thirty thousand protein structures determined by X-ray crystallography{,} the challenge of protein crystallization for 3D structure determination remains. In the quest for additives for efficient protein crystallization{,} inorganic materials emerge as an alternative. Magnetic particles (MPs) are versatile inorganic materials{,} easy to use{,} modify and manipulate in a wide range of biological assays. The potential of using functionalised MPs as crystallization chaperones for protein crystallization was shown in this work. MPs with distinct coatings were rationally designed to promote protein crystallization by affinity-triggered heterogeneous nucleation. Hen egg white lysozyme (HEWL) and trypsin{,} were crystallized in the presence of MPs either bare or coated with a polysaccharide (chitin) or a protein (casein){,} respectively. The addition of MPs was characterized in terms of bound protein to the MPs{,} crystal morphology{,} time-lapse of crystal emergence{,} crystallization yield fold change and crystal diffraction quality for structure determination. The MPs additives have shown to bind to the respective target protein{,} and to promote nucleation and crystal growth without compromising crystal morphology. On the other hand{,} MPs addition led to faster detectable crystal emergence and up to 13 times higher crystallization yield{,} addressing some the challenges in protein crystallization{,} the main bottleneck of macromolecular crystallography. Structure determination of the protein crystallized in the presence of MPs revealed that the structural characteristics of the protein remained unchanged{,} as shown by the superposition with PDB annotated proteins. Moreover{,} and unlike most reported cases{,} it was possible to exclude the inhibitor benzamidine during trypsin crystallisation{,} which is a remarkable result opening new prospects in enzyme engineering and drug design. Our results show that MPs coated with affinity ligands to target proteins can be used as controlled and tailor-made crystallization inducers.

Protein crystallization still remains mostly an empirical science, as the production of crystals with the required quality for X-ray analysis is dependent on the intensive screening of the best protein crystallization and crystal’s derivatization conditions. Herein, this demanding step was addressed by the development of a high-throughput and low-budget microfluidic platform consisting of an ion exchange membrane (117 Nafion® membrane) sandwiched between a channel layer (stripping phase compartment) and a wells layer (feed phase compartment) forming 75 independent micro-contactors. This microfluidic device allows for a simultaneous and independent screening of multiple protein crystallization and crystal derivatization conditions, using Hen Egg White Lysozyme (HEWL) as the model protein and Hg2+ as the derivatizing agent. This microdevice offers well-regulated crystallization and subsequent crystal derivatization processes based on the controlled transport of water and ions provided by the 117 Nafion® membrane. Diffusion coefficients of water and the derivatizing agent (Hg2+) were evaluated, showing the positive influence of the protein drop volume on the number of crystals and crystal size. This microfluidic system allowed for crystals with good structural stability and high X-ray diffraction quality and, thus, it is regarded as an efficient tool that may contribute to the enhancement of the proteins’ crystals structural resolution.

A novel composite has been prepared through the immobilization of the Keggin sandwich-type {[}Sm (PMo11O39)(2)](11-) anion (SmPOM) on large-pore silica spheres previously functionalized with trimethylammonium groups (TMA). The resulting SmPOM@TMA-LPMS material has been evaluated as heterogeneous catalyst in a biphasic desulfurization 1:1 diesel/extraction solvent system using H2O2 as oxidant. Preliminary experiments were conducted with different extraction solvents, acetonitrile and {[}BMIM]PF6 ionic liquid. The optimized extractive and catalytic oxidative desulfurization system (ECODS) with {[}BMIM]PF6 was able to reach complete sulfur removal from a model diesel containing 2100 ppm S in just 60 min (10 min of initial extraction + 50 min of catalytic step). The reutilization of catalyst and extraction phase has been successfully performed without loss of desulfurization efficiency in consecutive cycles, turning the process more sustainable and cog-effective. The remarkable results with simulated diesel have motivated the application of the catalyst in the desulfurization of untreated real diesel and 74% of efficiency was achieved after only 2 h for three consecutive cycles.

Novel material catalysts based in the active zinc-substituted polyoxotungstate ({[}PW11Zn(H2O)(39)](5-), abbreviated as PW11Zn) were efficiently used in the oxidative desulfurization of real and model diesels. These active catalytic center was strategically immobilized in a less hydrophilic periodic mesoporous organosilicas (PMOs), containing ethane-bridge (PMOE) and benzene-bridge (PMOB) walls, functionalized with (3-aminopropyl)triethoxysilane (aptes). The efficiency of the novel catalytic composites (PW11Zn@aptesPMOE and PM11Zn@aptesPMOB) was studied under oxidative desulfurization system (CODS) without the presence of an extraction solvent and also using a biphasic (diesel/extraction solvent) oxidative desulfurization system (ECODS). Both composites presented higher desulfurization efficiency under the solvent-free system, reaching ultra-low levels of sulfur compounds after only 1 h and using low ratio of H2O2/S = 4. The catalysts could be recycled without loss of activity for ten consecutive cycles. However, after the first desulfurization cycle complete desulfurization was achieved within only 30 min using PW11Zn@aptesPMOE composite. Also, the structure of PW it Zn@aptesPMOE demonstrated to be more stable than PW11Zn@aptesPMOB, probably due to the occurrence of some PW11Zn leaching from the PMOB surface, probably caused by the lower interaction of PW11Zn with the benzene-bridge PMOB wall. The most robust catalyst PW11Zn@aptesPMOE was used to desulfurize a real diesel achieving 75.9% of desulfurization after 2 h. The catalyst was further recycled with success to treat real diesel.

Magnetic hyperthermia is a cancer treatment based on the exposure of magnetic nanoparticles to an alternating magnetic field in order to generate local heat. In this work, 3D cell culture models were prepared to observe the effect that a different number of internalized particles had on the mechanisms of cell death triggered upon the magnetic hyperthermia treatment. Macrophages were selected by their high capacity to uptake nanoparticles. Intracellular nanoparticle concentrations up to 7.5 pg Fe/cell were measured both by elemental analysis and magnetic characterization techniques. Cell viability after the magnetic hyperthermia treatment was decreased to <25% for intracellular iron contents above 1 pg per cell. Theoretical calculations of the intracellular thermal effects that occurred during the alternating magnetic field application indicated a very low increase in the global cell temperature. Different apoptotic routes were triggered depending on the number of internalized particles. At low intracellular magnetic nanoparticle amounts (below 1 pg Fe/cell), the intrinsic route was the main mechanism to induce apoptosis, as observed by the high Bax/Bcl-2 mRNA ratio and low caspase-8 activity. In contrast, at higher concentrations of internalized magnetic nanoparticles (1−7.5 pg Fe/cell), the extrinsic route was observed through the increased activity of caspase-8. Nevertheless, both mechanisms may coexist at intermediate iron concentrations. Knowledge on the different mechanisms of cell death triggered after the magnetic hyperthermia treatment is fundamental to understand the biological events activated by this procedure and their role in its effectiveness.

Current cancer therapies are frequently ineffective and associated with severe side effects and with acquired cancer drug resistance. The development of effective therapies has been hampered by poor correlations between pre-clinical and clinical outcomes. Cancer cell-derived spheroids are three-dimensional (3D) structures that mimic layers of tumors in terms of oxygen and nutrient and drug resistance gradients. Gold nanoparticles (AuNP) are promising therapeutic agents which permit diminishing the emergence of secondary effects and increase therapeutic efficacy. In this work, 3D spheroids of Doxorubicin (Dox)-sensitive and -resistant colorectal carcinoma cell lines (HCT116 and HCT116-DoxR, respectively) were used to infer the potential of the combination of chemotherapy and Au-nanoparticle photothermy in the visible (green laser of 532 nm) to tackle drug resistance in cancer cells. Cell viability analysis of 3D tumor spheroids suggested that AuNPs induce cell death in the deeper layers of spheroids, further potentiated by laser irradiation. The penetration of Dox and earlier spheroid disaggregation is potentiated in combinatorial therapy with Dox, AuNP functionalized with polyethylene glycol (AuNP@PEG) and irradiation. The time point of Dox administration and irradiation showed to be important for spheroids destabilization. In HCT116-sensitive spheroids, pre-irradiation induced earlier disintegration of the 3D structure, while in HCT116 Dox-resistant spheroids, the loss of spheroid stability occurred almost instantly in post-irradiated spheroids, even with lower Dox concentrations. These results point towards the application of new strategies for cancer therapeutics, reducing side effects and resistance acquisition.

The pyogenic streptococci group includes pathogenic species for humans and other animals and has been associated with enduring morbidity and high mortality. The main reason for the treatment failure of streptococcal infections is the increased resistance to antibiotics. In recent years, infectious diseases caused by pyogenic streptococci resistant to multiple antibiotics have been raising with a significant impact to public health and veterinary industry. The rise of antibiotic-resistant streptococci has been associated to diverse mechanisms, such as efflux pumps and modifications of the antimicrobial target. Among streptococci, antibiotic resistance emerges from previously sensitive populations as result of horizontal gene transfer or chromosomal point mutations due to excessive use of antimicrobials. Streptococci strains are also recognized as biofilm producers. The increased resistance of biofilms to antibiotics among streptococci promote persistent infection, which comprise circa 80% of microbial infections in humans. Therefore, to overcome drug resistance, new strategies, including new antibacterial and antibiofilm agents, have been studied. Interestingly, the use of systems based on nanoparticles have been applied to tackle infection and reduce the emergence of drug resistance. Herein, we present a synopsis of mechanisms associated to drug resistance in (pyogenic) streptococci and discuss some innovative strategies as alternative to conventional antibiotics, such as bacteriocins, bacteriophage, and phage lysins, and metal nanoparticles. We shall provide focused discussion on the advantages and limitations of agents considering application, efficacy and safety in the context of impact to the host and evolution of bacterial resistance.

Part. Part. Syst. Charact. 2020, 37, 1900447 In the originally published manuscript, the author Márcia T. Tavares was omitted. The author is hereby added in the author byline and is associated with the first affiliation.